EVGA 122-M2-NF59-AX manual Floppy Drive a, Halt On, Memory

Page 31

•“None” means no HDD is installed or set.

•“Auto” means the system can auto-detect the hard disk when booting up •“Manual” mean the information can be entered manually. Note: “Access Mode” must also be set to “CHS” to enable manual entry.

Cylinder	Number of cylinders
Head	Number of heads

Precomp Write pre-compensation

Landing Zone Landing zone

Sector Number of sectors

Award (Phoenix) BIOS can support 3 HDD modules: CHS, LBA, and Large or

Auto mode.
CHS	For HDD < 528 MB
LBA	For HDD > 528	MB & supporting LBA (Logical Block Addressing)
Large	For HDD > 528	MB but not supporting LBA
Auto	Recommended mode

Floppy Drive A

This option allows you to select the kind of FDD to be installed, including “None”.

Halt On

This category determines whether or not the computer will stop if an error is detected during powering up.

All Errors Whenever the BIOS detects a nonfatal error, the system will stop and you will be prompted.

No Errors The system boot will not stop for any errors that may be detected.

All, But Keyboard	The system boot will not stop for a keyboard error; but it
will stop for all other errors.
All, But Diskette	The system boot will not stop for a diskette error; but it will
stop for all other errors.
All, But Disk/Key	The system boot will not stop for a keyboard or disk error,

but it will stop for all other errors.

Memory

This is a Display-Only category determined by POST (Power On Self Test) of the BIOS.

Base Memory

The BIOS POST will determine the amount of base (or conventional) memory installed in the system.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

Total Memory

Total memory of the system.

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 30

Image 31

Contents Page CPU Support Evga Nforce 590 SLI MotherboardTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan CPU Socket AM2 SpecificationsLayout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Cmos RAM Clear Setting Hardware Installation Hardware Installation StepsAbout AMD Athlon64 AM2 CPUs Install CPU GlossaryValid Memory Configurations Install MemoryFor Dual Channel Memory Assigning IRQs For Expansion Card Expansion Cards Procedure For Expansion Card InstallationPCI-Express Slots Interrupt Request Table For This MotherboardFrom TOP to Bottom IRQ Standard Interrupt AssignmentsSLI Bridge for Nvidia SLI Supported VGA Cards Page PIN ROW1 ROW2 Connectors and Headers Power Connector 24-pin block AtxpwrPS/2 Mouse & PS/2 Keyboard Connector KB ATX 12V Power Connector 8-pin block ATX12VLAN Port connector UL1 CEN/LEF Blackness MIC PinkPrimary IDE Connector 40-pin block IDE1 Floppy drive Connector 34-pin block FDDPin Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Serial-ATA Port ConnectorsAudio Headers Line-Out/MIC Header for Front Panel 9-pin AudioUSB Port Headers 9-pin USB1/USB2/USB3 Speak PwrledJW FP CD Audio-In Headers 4-pin Cdin FAN Headers 3-pin CPUFAN, SYSFAN1Supplemental SLI Power J2 Firewire Connectors 1394A~BBeep Meaning Starting Up Your ComputerAdvanced Chipset Features Bios Description Enter Bios SetupStandard Cmos Features Advanced Bios FeaturesSet User Name Load DefaultsSet Password Save & Exit SetupHalt On Floppy Drive aMemory Quick Power On Self Test Advanced Bios Features Removable Device PriorityHard Disk Boot Priority Network Boot PriorityLPC P2P P2P SPP MCP Ref Clock Frequency Settings Ref Clock HTTCPU Multiplier PCIe Bus, SlotCPU CKE power down control Memory Configuration Optimized for nForce MemDrive Strength setting CKE base power down modeRead delay from Rx Fifo Memory Timings Standard Memory Settings Timing modeCommand Per Clock CMD Advance Memory Settings tRRDMA drive strength Dram driver weak modeCKE drive strength CS drive strengthMAC Config IDE Function SetupRAID Config USB ConfigStates Support Power-on by AlarmPower on Function Acpi Suspend TypeIRQ Resources Reset Configuration DataInit Display First Resources Controlled byBoard Temperature ValuesPassword Disabled Press any key to continue… SystemQuit Without Saving Y/N? Save to Cmos and Exit Y/N?Nvidia Networking Guide Launching Nvidia Networking Enabling FirstPacket Configuring FirstPacketConfiguring TCP/IP Acceleration MediaShield RAID Manager Configuring TeamingCreate RAID Arrays Setting Up a Custom Array Configuration OptionsCreating a Mirrored Array View RAID Arrays RAID configuration information appears, as shown in FigureDelete Array Wizard Delete RAID ArraysAssigning a Free Disk Setting Up a Spare RAID DiskFree Disk Dedicated DiskStarting nTune Nvidia nTunrePerformance Category Adjust Motherboard SettingsAdjust GPU Settings Tune System Dynamic Bios AccessView System Information Adjust Custom RulesNvidia Monitor Perform Stability TestRAID Installation Driver InstallationPage Quick Debug Port Post Codes AppendixPage Page Page FCC Compliance Information COPYRIGHTS, TRADEMARKS, NoticesUseful Information Contacting Customer ServiceInformation to Keep Handy Before Calling