EVGA 122-M2-NF59-AX manual Layout Diagram & Jumper Settings

Page 8

Layout Diagram & Jumper Settings

5

1

2

34

1. PS/2 Mouse Port

This port is used to connect a PS/2 mouse

2. PS/2 Keyboard Port

This port is used to connect a PS/2 keyboard

3. IEEE1394b Port

This port is used to connect a 1394b device

4. USB 2.0 Ports

The six ports are used to connect USB 2.0 devices

5. LAN Ports

The left LED is no function (always off). The right LED function sees below table

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 7

Image 8

Contents Page Evga Nforce 590 SLI Motherboard CPU SupportTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan Specifications CPU Socket AM2Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Hardware Installation Hardware Installation Steps Cmos RAM Clear SettingInstall CPU Glossary About AMD Athlon64 AM2 CPUsInstall Memory Valid Memory ConfigurationsFor Dual Channel Memory Expansion Cards Procedure For Expansion Card Installation Assigning IRQs For Expansion CardFrom TOP to Bottom Interrupt Request Table For This MotherboardPCI-Express Slots Standard Interrupt Assignments IRQSLI Bridge for Nvidia SLI Supported VGA Cards Page Connectors and Headers Power Connector 24-pin block Atxpwr PIN ROW1 ROW2LAN Port connector UL1 ATX 12V Power Connector 8-pin block ATX12VPS/2 Mouse & PS/2 Keyboard Connector KB MIC Pink CEN/LEF BlacknessPin Floppy drive Connector 34-pin block FDDPrimary IDE Connector 40-pin block IDE1 Serial-ATA Port Connectors Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATAUSB Port Headers 9-pin USB1/USB2/USB3 Headers Line-Out/MIC Header for Front Panel 9-pin AudioAudio JW FP PwrledSpeak FAN Headers 3-pin CPUFAN, SYSFAN1 CD Audio-In Headers 4-pin CdinFirewire Connectors 1394A~B Supplemental SLI Power J2Starting Up Your Computer Beep MeaningBios Description Enter Bios Setup Standard Cmos FeaturesAdvanced Bios Features Advanced Chipset FeaturesLoad Defaults Set PasswordSave & Exit Setup Set User NameMemory Floppy Drive aHalt On Advanced Bios Features Removable Device Priority Hard Disk Boot PriorityNetwork Boot Priority Quick Power On Self TestLPC P2P P2P Frequency Settings Ref Clock HTT CPU MultiplierPCIe Bus, Slot SPP MCP Ref ClockCPU Memory Configuration Optimized for nForce Mem Drive Strength settingCKE base power down mode CKE power down controlMemory Timings Standard Memory Settings Timing mode Command Per Clock CMDAdvance Memory Settings tRRD Read delay from Rx FifoDram driver weak mode CKE drive strengthCS drive strength MA drive strengthIDE Function Setup RAID ConfigUSB Config MAC ConfigPower-on by Alarm Power on FunctionAcpi Suspend Type States SupportReset Configuration Data Init Display FirstResources Controlled by IRQ ResourcesTemperature Values Password Disabled Press any key to continue…System BoardNvidia Networking Guide Launching Nvidia Networking Save to Cmos and Exit Y/N?Quit Without Saving Y/N? Configuring FirstPacket Enabling FirstPacketConfiguring TCP/IP Acceleration Configuring Teaming MediaShield RAID ManagerCreate RAID Arrays Configuration Options Setting Up a Custom ArrayCreating a Mirrored Array RAID configuration information appears, as shown in Figure View RAID ArraysDelete RAID Arrays Delete Array WizardSetting Up a Spare RAID Disk Free DiskDedicated Disk Assigning a Free DiskNvidia nTunre Starting nTuneAdjust Motherboard Settings Performance CategoryAdjust GPU Settings Dynamic Bios Access Tune SystemAdjust Custom Rules View System InformationPerform Stability Test Nvidia MonitorDriver Installation RAID InstallationPage Appendix Quick Debug Port Post CodesPage Page Page COPYRIGHTS, TRADEMARKS, Notices FCC Compliance InformationInformation to Keep Handy Before Calling Contacting Customer ServiceUseful Information