EVGA 122-M2-NF59-AX manual Dynamic Bios Access, Tune System

Page 56

Dynamic BIOS Access

This page allows you to change your system BIOS settings. The changes do not go into effect until after you reboot your system. Since these changes are made to actual BIOS settings in the CMOS, the settings remain active until you change them again or restore the CMOS to the default settings.

In the Dynamic BIOS Access page, click the Available BIOS Pages list arrow and click the BIOS page that you want to edit. The BIOS page chosen determines which items on the page are available for changing. To edit an item, click the corresponding list arrow and then click one of the values from the list. When finished making your changes, click the OK or Apply.

NOTE: This feature is available only with BIOS support from the motherboard manufacturer.

Tune System

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 55

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Page Evga Nforce 590 SLI Motherboard CPU SupportTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan Specifications CPU Socket AM2Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Hardware Installation Hardware Installation Steps Cmos RAM Clear SettingInstall CPU Glossary About AMD Athlon64 AM2 CPUsInstall Memory Valid Memory ConfigurationsFor Dual Channel Memory Expansion Cards Procedure For Expansion Card Installation Assigning IRQs For Expansion CardFrom TOP to Bottom Interrupt Request Table For This MotherboardPCI-Express Slots Standard Interrupt Assignments IRQSLI Bridge for Nvidia SLI Supported VGA Cards Page Connectors and Headers Power Connector 24-pin block Atxpwr PIN ROW1 ROW2LAN Port connector UL1 ATX 12V Power Connector 8-pin block ATX12VPS/2 Mouse & PS/2 Keyboard Connector KB MIC Pink CEN/LEF BlacknessPin Floppy drive Connector 34-pin block FDDPrimary IDE Connector 40-pin block IDE1 Serial-ATA Port Connectors Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATAUSB Port Headers 9-pin USB1/USB2/USB3 Headers Line-Out/MIC Header for Front Panel 9-pin AudioAudio JW FP PwrledSpeak FAN Headers 3-pin CPUFAN, SYSFAN1 CD Audio-In Headers 4-pin CdinFirewire Connectors 1394A~B Supplemental SLI Power J2Starting Up Your Computer Beep MeaningBios Description Enter Bios Setup Standard Cmos FeaturesAdvanced Bios Features Advanced Chipset FeaturesLoad Defaults Set PasswordSave & Exit Setup Set User NameMemory Floppy Drive aHalt On Advanced Bios Features Removable Device Priority Hard Disk Boot PriorityNetwork Boot Priority Quick Power On Self TestLPC P2P P2P Frequency Settings Ref Clock HTT CPU MultiplierPCIe Bus, Slot SPP MCP Ref ClockCPU Memory Configuration Optimized for nForce Mem Drive Strength settingCKE base power down mode CKE power down controlMemory Timings Standard Memory Settings Timing mode Command Per Clock CMDAdvance Memory Settings tRRD Read delay from Rx FifoDram driver weak mode CKE drive strengthCS drive strength MA drive strengthIDE Function Setup RAID ConfigUSB Config MAC ConfigPower-on by Alarm Power on FunctionAcpi Suspend Type States SupportReset Configuration Data Init Display FirstResources Controlled by IRQ ResourcesTemperature Values Password Disabled Press any key to continue…System BoardNvidia Networking Guide Launching Nvidia Networking Save to Cmos and Exit Y/N?Quit Without Saving Y/N? Configuring FirstPacket Enabling FirstPacketConfiguring TCP/IP Acceleration Configuring Teaming MediaShield RAID ManagerCreate RAID Arrays Configuration Options Setting Up a Custom ArrayCreating a Mirrored Array RAID configuration information appears, as shown in Figure View RAID ArraysDelete RAID Arrays Delete Array WizardSetting Up a Spare RAID Disk Free DiskDedicated Disk Assigning a Free DiskNvidia nTunre Starting nTuneAdjust Motherboard Settings Performance CategoryAdjust GPU Settings Dynamic Bios Access Tune SystemAdjust Custom Rules View System InformationPerform Stability Test Nvidia MonitorDriver Installation RAID InstallationPage Appendix Quick Debug Port Post CodesPage Page Page COPYRIGHTS, TRADEMARKS, Notices FCC Compliance InformationInformation to Keep Handy Before Calling Contacting Customer ServiceUseful Information
Top Page Image Contents