EVGA 122-M2-NF59-AX IDE Function Setup, RAID Config, USB Config, MAC Config, IEEE1394 controller

Page 39

IDE Function Setup

Use this menu to setup the data flow control for IDE

RAID Config

Use this menu to enable/disable SATA RAID

USB Config

Use this menu to setup USB interface

MAC Config

Use this menu to turn off MAC

IEEE1394 controller

Use this setting to set whether the IEEE 1394 function is enabled.

HD Audio

Use this setting to configure HD Audio

IDE HDD Block Mode

Use this setting to configure HDD Block Mode

Onboard FDC Controller

This option is used to set whether the Onboard FDC Controller is enabled.

Onboard Serial Port 1

This option is used to assign the I/O address and IRQ for onboard serial port 1.

Power Management Setup

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 38

Image 39

Contents Page CPU Support Evga Nforce 590 SLI MotherboardTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan CPU Socket AM2 SpecificationsLayout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Cmos RAM Clear Setting Hardware Installation Hardware Installation StepsAbout AMD Athlon64 AM2 CPUs Install CPU GlossaryValid Memory Configurations Install MemoryFor Dual Channel Memory Assigning IRQs For Expansion Card Expansion Cards Procedure For Expansion Card InstallationInterrupt Request Table For This Motherboard PCI-Express SlotsFrom TOP to Bottom IRQ Standard Interrupt AssignmentsSLI Bridge for Nvidia SLI Supported VGA Cards Page PIN ROW1 ROW2 Connectors and Headers Power Connector 24-pin block AtxpwrATX 12V Power Connector 8-pin block ATX12V PS/2 Mouse & PS/2 Keyboard Connector KBLAN Port connector UL1 CEN/LEF Blackness MIC PinkFloppy drive Connector 34-pin block FDD Primary IDE Connector 40-pin block IDE1Pin Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Serial-ATA Port ConnectorsHeaders Line-Out/MIC Header for Front Panel 9-pin Audio AudioUSB Port Headers 9-pin USB1/USB2/USB3 Pwrled SpeakJW FP CD Audio-In Headers 4-pin Cdin FAN Headers 3-pin CPUFAN, SYSFAN1Supplemental SLI Power J2 Firewire Connectors 1394A~BBeep Meaning Starting Up Your ComputerAdvanced Chipset Features Bios Description Enter Bios SetupStandard Cmos Features Advanced Bios FeaturesSet User Name Load DefaultsSet Password Save & Exit SetupFloppy Drive a Halt OnMemory Quick Power On Self Test Advanced Bios Features Removable Device PriorityHard Disk Boot Priority Network Boot PriorityLPC P2P P2P SPP MCP Ref Clock Frequency Settings Ref Clock HTTCPU Multiplier PCIe Bus, SlotCPU CKE power down control Memory Configuration Optimized for nForce MemDrive Strength setting CKE base power down modeRead delay from Rx Fifo Memory Timings Standard Memory Settings Timing modeCommand Per Clock CMD Advance Memory Settings tRRDMA drive strength Dram driver weak modeCKE drive strength CS drive strengthMAC Config IDE Function SetupRAID Config USB ConfigStates Support Power-on by AlarmPower on Function Acpi Suspend TypeIRQ Resources Reset Configuration DataInit Display First Resources Controlled byBoard Temperature ValuesPassword Disabled Press any key to continue… SystemSave to Cmos and Exit Y/N? Quit Without Saving Y/N?Nvidia Networking Guide Launching Nvidia Networking Enabling FirstPacket Configuring FirstPacketConfiguring TCP/IP Acceleration MediaShield RAID Manager Configuring TeamingCreate RAID Arrays Setting Up a Custom Array Configuration OptionsCreating a Mirrored Array View RAID Arrays RAID configuration information appears, as shown in FigureDelete Array Wizard Delete RAID ArraysAssigning a Free Disk Setting Up a Spare RAID DiskFree Disk Dedicated DiskStarting nTune Nvidia nTunrePerformance Category Adjust Motherboard SettingsAdjust GPU Settings Tune System Dynamic Bios AccessView System Information Adjust Custom RulesNvidia Monitor Perform Stability TestRAID Installation Driver InstallationPage Quick Debug Port Post Codes AppendixPage Page Page FCC Compliance Information COPYRIGHTS, TRADEMARKS, NoticesContacting Customer Service Useful InformationInformation to Keep Handy Before Calling