EVGA 122-M2-NF59-AX manual LPC P2P P2P

Page 33

Advanced Chipset Features

Use this section to control chipset features, specifically clocks, voltages, and memory timings.

System Clocks

Use this menu to control system clocks (see System Clocks section below)

System Voltages

Use this menu to control system voltages (see System Voltages section below)

Memory Configuration

Use this menu to control memory settings (see Memory Configuration section below)

PCI Clocks

Use this menu to turn off the PCI clock on the unused PCI slot

LPC P2P P2P

Decoding mode for LPC and P2P

SSE/SSE2 Instructions

Enable/Disable Stream SIMD Extensions

System BIOS Cacheable

Enable the memory cache function for BIOS

Load timing/voltage settings

Load timing and voltage settings from a profile

Save timing/voltage settings

Save timing and voltage settings to a profile

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 32

Image 33
Contents Page CPU Support Evga Nforce 590 SLI MotherboardTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan CPU Socket AM2 SpecificationsLayout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Cmos RAM Clear Setting Hardware Installation Hardware Installation StepsAbout AMD Athlon64 AM2 CPUs Install CPU GlossaryValid Memory Configurations Install MemoryFor Dual Channel Memory Assigning IRQs For Expansion Card Expansion Cards Procedure For Expansion Card InstallationInterrupt Request Table For This Motherboard PCI-Express SlotsFrom TOP to Bottom IRQ Standard Interrupt AssignmentsSLI Bridge for Nvidia SLI Supported VGA Cards Page PIN ROW1 ROW2 Connectors and Headers Power Connector 24-pin block AtxpwrATX 12V Power Connector 8-pin block ATX12V PS/2 Mouse & PS/2 Keyboard Connector KBLAN Port connector UL1 CEN/LEF Blackness MIC PinkFloppy drive Connector 34-pin block FDD Primary IDE Connector 40-pin block IDE1Pin Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Serial-ATA Port ConnectorsHeaders Line-Out/MIC Header for Front Panel 9-pin Audio AudioUSB Port Headers 9-pin USB1/USB2/USB3 Pwrled SpeakJW FP CD Audio-In Headers 4-pin Cdin FAN Headers 3-pin CPUFAN, SYSFAN1Supplemental SLI Power J2 Firewire Connectors 1394A~BBeep Meaning Starting Up Your ComputerStandard Cmos Features Bios Description Enter Bios SetupAdvanced Bios Features Advanced Chipset FeaturesSet Password Load DefaultsSave & Exit Setup Set User NameFloppy Drive a Halt OnMemory Hard Disk Boot Priority Advanced Bios Features Removable Device PriorityNetwork Boot Priority Quick Power On Self TestLPC P2P P2P CPU Multiplier Frequency Settings Ref Clock HTTPCIe Bus, Slot SPP MCP Ref ClockCPU Drive Strength setting Memory Configuration Optimized for nForce MemCKE base power down mode CKE power down controlCommand Per Clock CMD Memory Timings Standard Memory Settings Timing modeAdvance Memory Settings tRRD Read delay from Rx FifoCKE drive strength Dram driver weak modeCS drive strength MA drive strengthRAID Config IDE Function SetupUSB Config MAC ConfigPower on Function Power-on by AlarmAcpi Suspend Type States SupportInit Display First Reset Configuration DataResources Controlled by IRQ ResourcesPassword Disabled Press any key to continue… Temperature ValuesSystem BoardSave to Cmos and Exit Y/N? Quit Without Saving Y/N?Nvidia Networking Guide Launching Nvidia Networking Enabling FirstPacket Configuring FirstPacketConfiguring TCP/IP Acceleration MediaShield RAID Manager Configuring TeamingCreate RAID Arrays Setting Up a Custom Array Configuration OptionsCreating a Mirrored Array View RAID Arrays RAID configuration information appears, as shown in FigureDelete Array Wizard Delete RAID ArraysFree Disk Setting Up a Spare RAID DiskDedicated Disk Assigning a Free DiskStarting nTune Nvidia nTunrePerformance Category Adjust Motherboard SettingsAdjust GPU Settings Tune System Dynamic Bios AccessView System Information Adjust Custom RulesNvidia Monitor Perform Stability TestRAID Installation Driver InstallationPage Quick Debug Port Post Codes AppendixPage Page Page FCC Compliance Information COPYRIGHTS, TRADEMARKS, NoticesContacting Customer Service Useful InformationInformation to Keep Handy Before Calling