EVGA 122-M2-NF59-AX manual Table of Contents

Page 4

TABLE OF CONTENTS (Continued)

Nvidia Networking Guide (continued)
Configuring TCP/IP Acceleration	45
Configuring Teaming	46
MediaShield RAID Manager	46
Create RAID Arrays	47
Nvidia nTune 5.0	53
Starting nTune	53
Adjust Motherboard Settings	54
Adjust GPU Settings	55
Dynamic BIOS Access	56
Tune System	56
View System Information	57
Nvidia Monitor	29
Driver Installation	59
RAID Installation
APPENDIX 1 - POST CODES	61
Quick Debug POST Codes	61
Boot Block POST Codes	62
APPENDIX 2 - TRADEMARKS AND NOTICES	64
Copyrights, Trademarks, and Notices	64
FCC Compliance Statement	64
APPENDIX 3 - CONTACTING SUPPORT AND OTHER USEFUL INFORMATION	65

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 3

Image 4

Contents Page Evga Nforce 590 SLI Motherboard CPU SupportTable of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan Specifications CPU Socket AM2Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Hardware Installation Hardware Installation Steps Cmos RAM Clear SettingInstall CPU Glossary About AMD Athlon64 AM2 CPUsInstall Memory Valid Memory ConfigurationsFor Dual Channel Memory Expansion Cards Procedure For Expansion Card Installation Assigning IRQs For Expansion CardPCI-Express Slots Interrupt Request Table For This MotherboardFrom TOP to Bottom Standard Interrupt Assignments IRQSLI Bridge for Nvidia SLI Supported VGA Cards Page Connectors and Headers Power Connector 24-pin block Atxpwr PIN ROW1 ROW2PS/2 Mouse & PS/2 Keyboard Connector KB ATX 12V Power Connector 8-pin block ATX12VLAN Port connector UL1 MIC Pink CEN/LEF BlacknessPrimary IDE Connector 40-pin block IDE1 Floppy drive Connector 34-pin block FDDPin Serial-ATA Port Connectors Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATAAudio Headers Line-Out/MIC Header for Front Panel 9-pin AudioUSB Port Headers 9-pin USB1/USB2/USB3 Speak PwrledJW FP FAN Headers 3-pin CPUFAN, SYSFAN1 CD Audio-In Headers 4-pin CdinFirewire Connectors 1394A~B Supplemental SLI Power J2Starting Up Your Computer Beep MeaningBios Description Enter Bios Setup Standard Cmos FeaturesAdvanced Bios Features Advanced Chipset FeaturesLoad Defaults Set PasswordSave & Exit Setup Set User NameHalt On Floppy Drive aMemory Advanced Bios Features Removable Device Priority Hard Disk Boot PriorityNetwork Boot Priority Quick Power On Self TestLPC P2P P2P Frequency Settings Ref Clock HTT CPU MultiplierPCIe Bus, Slot SPP MCP Ref ClockCPU Memory Configuration Optimized for nForce Mem Drive Strength settingCKE base power down mode CKE power down controlMemory Timings Standard Memory Settings Timing mode Command Per Clock CMDAdvance Memory Settings tRRD Read delay from Rx FifoDram driver weak mode CKE drive strengthCS drive strength MA drive strengthIDE Function Setup RAID ConfigUSB Config MAC ConfigPower-on by Alarm Power on FunctionAcpi Suspend Type States SupportReset Configuration Data Init Display FirstResources Controlled by IRQ ResourcesTemperature Values Password Disabled Press any key to continue…System BoardQuit Without Saving Y/N? Save to Cmos and Exit Y/N?Nvidia Networking Guide Launching Nvidia Networking Configuring FirstPacket Enabling FirstPacketConfiguring TCP/IP Acceleration Configuring Teaming MediaShield RAID ManagerCreate RAID Arrays Configuration Options Setting Up a Custom ArrayCreating a Mirrored Array RAID configuration information appears, as shown in Figure View RAID ArraysDelete RAID Arrays Delete Array WizardSetting Up a Spare RAID Disk Free DiskDedicated Disk Assigning a Free DiskNvidia nTunre Starting nTuneAdjust Motherboard Settings Performance CategoryAdjust GPU Settings Dynamic Bios Access Tune SystemAdjust Custom Rules View System InformationPerform Stability Test Nvidia MonitorDriver Installation RAID InstallationPage Appendix Quick Debug Port Post CodesPage Page Page COPYRIGHTS, TRADEMARKS, Notices FCC Compliance InformationUseful Information Contacting Customer ServiceInformation to Keep Handy Before Calling