Echo EN55022 manual Appendix a Warnings, This Equipment Must be Earthed, Grounded

Page 44

 

APPENDIX A WARNINGS

WARNING:

THIS EQUIPMENT MUST BE EARTHED/

 

GROUNDED

 

This equipment relies on the EARTH /

 

GROUND connection to ensure safe operation

 

such that the user and TELECOM Network are

 

adequately protected. It must not under any

 

circumstances be operated without an earth

 

connection, which could nullify its approval

 

for connection to a network.

WARNING:

INSTALLATION OF EQUIPMENT

 

Installation of this equipment must only be

 

performed by suitably trained service

 

personnel.

WARNING:

CONNECTION OF OTHER EQUIPMENT

 

This equipment allows connection only of

 

suitably approved equipment to its ports, the

 

safety status of which are defined below.

 

SELV Ports:

 

i)

Supervisor port

 

ii)

MAIN port

 

iii)

D&I port

 

iv)

CH1 and CH2 (Channel ports)

 

v)

EXT CLOCK

 

vi)

ALARM port

 

vii)

AUI port

 

viii)

10BASE-T port

The above named ports are classified as SELV (Safety Extra Low Voltage) in accordance with in Clause 2.3 of EN60950 (BS7002, IEC950 as applicable), and must only be connected to equipment which similarly complies with the SELV safety classification.

Echo LANlink Router Option User Manual

Issue 1.0 04 December 1997 Page 44 of 59

Image 44
Contents Page 5SXLANlink Contents Issue 1.0 04 December 1997 Page 4 Glossary Introduction Linking two LANs togetherFunctional Overview Typical ApplicationsRestrictive Firewall Example USE and Configuration Router Configuration Supervisor Terminal RequirementsLogin Default terminal VT 100/220/320/420. OK y or n?Return Falco Sunview WYSE50SUN Supported Terminal TypesRouter Management Router Management Screen General Keyboard ConventionsEntering a Parameter Multiplexer Management Megabit E1 MultiplexerClearing the Configuration back to Factory Default System StatusRemote Alarm Main Link High BIT Error Rate8 D/I Remote Alarm Main Link Carrier LossRouter WAN Link Status Installation Opening the MultiplexerInstalling the Router Option Internal Link LK13Testing Data ConnectionsFront Panel LEDs LED LabelQuick Configuration IPX Configuration Receive IP RIPTransmit IP RIP IP BroadcastReceive IPX RIP Transmit IPX RIPReceive IPX SAP Transmit IPX SAPParameter Description Options Router Menu OptionsUnit Status Traffic Analysis IP Routing TableParameter Description IP ARP TableIPX RIP Table IPX NetworkNode HopsSocket IPX SAP TableType Network Loading Show Traffic DetailsTelnet OUT Name Server ConfigurationRemote Management Name to IP Cache Parameter Description Security Parameter Description OptionsUnit Configuration Snmp Setup Parameter DescriptionService Setup Ethernet Service Setup Parameter Description OptionsIP Broadcast OnesZeros IP FilterWAN Service Setup Parameter Description Options PPP Setup OtherMenu Selection Description Filter SetupMAC Filters WAN or Ethernet IP Filter WAN or Ethernet EditList Parameter Description LineIPX SAP Filter Menu WAN or Ethernet Network Address 32 bitsNode Address 48 bits From SKTALL To SKTIPX Header Filters Novell KEEP-ALIVES EventsMAC Node ADR PPP Events System EventsFlash Programming Timeout Flash Verify Error Installation of Equipment Appendix a WarningsThis Equipment Must be Earthed GroundedWarnung Mise en garde Connexion dautres équipements Mise en garde Installation de léquipmentMise en garde Cet équipement doit être relié a la terre Appendix B Approval Requirements Appendix C EMC Requirements Appendix D Rear Panel Layout Appendix E AUI Port 15-WAYD-TYPE Pinout Appendix F 10BASE-T RJ45 Port Pinout TPTX+Tptx TPRX+Appendix G IP Filter Examples Source and Destination IP AddressSource and Destination Ports ExamplesProtocol Selection Issue 1.0 04 December 1997 Page 54 Appendix H IP Subnets Appendix I Router Maintenance Menu KermitCTRL-A CTRL-BRestore Configuration using Tftp Download New Firmware using TCP loaderDownload New Firmware using Tftp Set Default Gateway Reset PasswordBoot File Using TCP Loader Set New IP AddressBoot File Using Tftp Loader Run Monitor