Dell M630 owner manual Replacing an SD card

Page 56

Replacing an SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Ensure that you read the Safety instructions.

2.Follow the procedure listed in Before working inside your system.

3.Enter the System Setup and ensure that the Internal SD Card Port is enabled.

CAUTION: When an SD card failure occurs, and the Internal SD Card Redundancy option in the Integrated Devices screen of the System Setup is set to Mirror Mode, there may be loss of data. To avoid data loss, follow step 4 through step 6 of Troubleshooting an internal SD card.

NOTE: The SD card in the lower card slot is the primary card (SD1) and the SD card in the upper card slot is the secondary card (SD2).

NOTE: When an SD card failure occurs, the Internal SD Card Redundancy option in the System Setup is set to Disabled and the internal dual SD module controller notifies the system. On the next reboot, the system displays a message indicating the failure.

NOTE: If the Internal SD Card Redundancy option is set to Disabled, replace the failed SD card with a new SD card.

Steps

1.Locate the SD card slot on the internal dual SD module (IDSDM) card.

2.Press inward on the card to release it from the slot, and remove the card.

56

Image 56

Contents Dell PowerEdge M630 Page Contents Installing and removing blade components Troubleshooting your system Technical specifications 107 Getting help 112 Using System Diagnostics 102Jumpers and connectors 104 Front-panel features and indicators About your systemUsing USB diskette or USB DVD/CD drives Hard-drive/SSD indicator patternsIDRAC Direct LED indicator codes Hard-drive/SSD indicatorsIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up your system Setting up and configuring the iDRAC IP addressLogging in to iDRAC Installing the operating system Page About System Setup Navigation keysSystem Bios screen Entering System SetupSystem Setup Main Menu System Information screen System Memory screenProcessor Settings screen ATSSata Settings screen Post Page Boot Settings screen Network Settings screenIntegrated Devices screen Serial Communication screen 4GBSystem Profile Settings screen C1ESystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screen About Boot Manager About Dell Lifecycle Controller Changing the boot orderEntering Boot Manager Boot Manager main menuChoosing the system boot mode Assigning a system and/or setup passwordUsing your system password to secure your system Embedded systems management Operating with a setup password enabledIDRAC Settings utility Entering the iDRAC Settings utility Safety instructions Recommended toolsBefore working inside your system After working inside your systemRemoving and installing a blade Removing the bladeBlade cover O connector cover Installing a blade Removing or installing the bladeRemoving and installing the system cover Removing the system coverInstalling the system cover Inside the blade Inside the bladeCooling shroud Removing the cooling shroudRemoving a processor/DIMM blank Installing the cooling shroudProcessor/DIMM blank Installing a processor/DIMM blank Removing and installing a processor/DIMM blankSystem memory LrdimmProcessor General memory module installation guidelines Mode-specific guidelines Advanced ECC LockstepSample memory configurations Memory configurations two processors Removing memory modules Installing memory modules Removing the memory moduleMezzanine card installation guidelines Module mezzanine cardsRemoving and installing the mezzanine card Removing the mezzanine cardInstalling the mezzanine card Idsdm card optionalReplacing an SD card Internal USB key Replacing an SD cardReplacing the internal USB key Removing and installing the Idsdm card Removing the Idsdm cardInstalling the Idsdm card RSPI card optional Removing the rSPI cardReplacing the SD vFlash card Installing the rSPI cardSD vFlash card Network Daughter Card Removing the Network Daughter CardNDC Installing the Network Daughter Card ProcessorsRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing a processor Installing and removing a processorPage Applying thermal grease on the top of the processor Hard-drive/SSD bay numbering Hard drive/SSD installation guidelinesHard drives/SSDs Removing and installing a hard drive/SSD Removing a hard drive/SSDInstalling a hard drive/SSD Removing a hard-drive/SSD blankHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Installing a 1.8 inch SSD in a 1.8 inch SSD carrier Removing the hard-drive/SSD cageHard-drive/SSD cage Screw Guide pin Removing the hard-drive/SSD backplane Installing the hard-drive/SSD cageHard-drive/SSD backplane Page Removing and installing the 1.8 inch x4 SSD backplane Removing the system board Installing the hard-drive/SSD backplaneSystem board Page Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Entering the system Service Tag using System Setup Trusted Platform ModuleRe-enabling the TPM for BitLocker users Nvram backup battery Replacing the Nvram backup batteryReplacing the Nvram backup battery Storage controller card/PCIe extender card Removing the PCIe extender/storage controller cardPage Installing the PCIe extender/storage controller card Troubleshooting your system Troubleshooting hard drives Troubleshooting Solid State Drives Troubleshooting USB devicesTroubleshooting an internal SD card Troubleshooting processorsTroubleshooting the blade system board Troubleshooting the Nvram backup batteryAlert messages Diagnostic messagesSystem messages Running the Embedded System Diagnostics Dell Embedded System DiagnosticsWhen to use the Embedded System Diagnostics Running embedded system diagnostics from an external media System diagnostic controlsJumpers and connectors System board jumper settingsSystem board connectors CPU1Disabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Enclosure can be installed with blade Documentation feedback Locating your system Service TagContacting Dell 113