Dell M630 owner manual Hard-drive/SSD backplane, Installing the hard-drive/SSD cage

Page 81

Installing the hard-drive/SSD cage

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

NOTE: You must remove the hard-drive/SSD cage to replace a faulty hard-drive/SSD cage or service other components inside the system.

1.Ensure that you read the Safety instructions.

2.Keep the #1 Phillips screwdriver ready.

3.Remove the hard-drive/SSD cage, see Removing the hard-drive/SSD cage.

Steps

1.Align the screw holes on the hard-drive/SSD cage with the screw holes on the chassis.

2.Lower the hard-drive/SSD cage into the chassis until it is seated firmly in place.

3.Install the four screws to secure the hard-drive/SSD cage to the chassis.

Next steps

1.Install the hard-drive/SSD backplane.

2.Install the hard drive/SSDs.

3.Follow the procedure listed in After working inside your system.

Hard-drive/SSD backplane

Removing the hard-drive/SSD backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To prevent damage to the hard drives/SSDs and the hard-drive/SSD backplane, you must remove the hard drives/SSDs from the blade before removing the hard-drive/SSD backplane.

CAUTION: Note the number of each hard drive/SSD and temporarily label them before removal so that you can replace them in the same locations.

1.Ensure that you read the Safety instructions.

2.Keep the #2 Phillips screwdriver ready.

3.Follow the procedure listed in Before working inside your system.

4.Remove the hard drive(s)/SSD(s).

81

Image 81
Contents Dell PowerEdge M630 Page Contents Installing and removing blade components Troubleshooting your system Using System Diagnostics 102 Jumpers and connectors 104Technical specifications 107 Getting help 112 About your system Front-panel features and indicatorsHard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drivesHard-drive/SSD indicators IDRAC Direct LED indicator codesIDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your systemLogging in to iDRAC Installing the operating system Page Navigation keys About System SetupEntering System Setup System Setup Main MenuSystem Bios screen System Memory screen System Information screenATS Processor Settings screenSata Settings screen Post Page Network Settings screen Boot Settings screenIntegrated Devices screen 4GB Serial Communication screenC1E System Profile Settings screenSystem Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screen About Dell Lifecycle Controller Changing the boot order About Boot ManagerEntering Boot Manager Boot Manager main menuAssigning a system and/or setup password Choosing the system boot modeUsing your system password to secure your system Operating with a setup password enabled IDRAC Settings utilityEmbedded systems management Entering the iDRAC Settings utility Recommended tools Safety instructionsBefore working inside your system After working inside your systemRemoving the blade Removing and installing a bladeBlade cover O connector cover Removing or installing the blade Installing a bladeRemoving the system cover Removing and installing the system coverInstalling the system cover Inside the blade Inside the bladeRemoving the cooling shroud Cooling shroudInstalling the cooling shroud Processor/DIMM blankRemoving a processor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blankLrdimm System memoryProcessor General memory module installation guidelines Advanced ECC Lockstep Mode-specific guidelinesSample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modulesModule mezzanine cards Mezzanine card installation guidelinesRemoving the mezzanine card Removing and installing the mezzanine cardIdsdm card optional Installing the mezzanine cardReplacing an SD card Replacing an SD card Internal USB keyReplacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm cardInstalling the Idsdm card Removing the rSPI card RSPI card optionalInstalling the rSPI card SD vFlash cardReplacing the SD vFlash card Removing the Network Daughter Card Network Daughter CardNDC Processors Installing the Network Daughter CardRemoving a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard drive/SSD installation guidelines Hard drives/SSDsHard-drive/SSD bay numbering Removing a hard drive/SSD Removing and installing a hard drive/SSDRemoving a hard-drive/SSD blank Installing a hard drive/SSDHard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrierHard-drive/SSD cage Screw Guide pin Installing the hard-drive/SSD cage Hard-drive/SSD backplaneRemoving the hard-drive/SSD backplane Page Removing and installing the 1.8 inch x4 SSD backplane Installing the hard-drive/SSD backplane System boardRemoving the system board Page Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Entering the system Service Tag using System SetupRe-enabling the TPM for BitLocker users Replacing the Nvram backup battery Nvram backup batteryReplacing the Nvram backup battery Removing the PCIe extender/storage controller card Storage controller card/PCIe extender cardPage Installing the PCIe extender/storage controller card Troubleshooting your system Troubleshooting hard drives Troubleshooting USB devices Troubleshooting Solid State DrivesTroubleshooting processors Troubleshooting an internal SD cardTroubleshooting the Nvram backup battery Troubleshooting the blade system boardDiagnostic messages System messagesAlert messages Dell Embedded System Diagnostics When to use the Embedded System DiagnosticsRunning the Embedded System Diagnostics System diagnostic controls Running embedded system diagnostics from an external mediaSystem board jumper settings Jumpers and connectorsCPU1 System board connectorsDisabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Enclosure can be installed with blade Locating your system Service Tag Contacting DellDocumentation feedback 113