Diamond Systems LX800 PC/104 user manual XOR Bit Select, Video Memory Size, Output display

Page 34

BIOS

XOR MB0

Setting: Disabled (Default), Enabled.

XOR Bit Select

Setting: 18 (Default), 19, 20, 21.

Video Memory Size

In order to determine how much memory is allocated to the video graphics device.

Setting: None, 8M (Default), 16M, 32M, 64M, 128M, 254M.

Output display

In order to specify the display devices the system is connected to. Setting: Flat Panel, CRT (Default), Panel & CRT.

)O W3 Q O&RQ¿JXU WLRQ

,W OORZV\RXWRRSHQWKH)O W3 QHO&RQ¿JXU WLRQPHQX

Memory Hole At 15M-16M

In order to improve performance, certain space in memory can be reserved for ISA cards. This memory must be mapped into the memory space below 16 MB.

Setting: Disabled (Default), Enabled.

- 31 -

Image 34

Contents Rhodeus-LC Table of Contents Appendix Introduction Copyright Notice About User’s ManualReplacing the lithium battery Technical SupportWarranty Packing List Ordering InformationBios 6S L¿ WlrqBoard Dimensions Introduction Unitmm Installation Block Diagrams AMD Geode LX800 CPU 500MHzJumpers and Connectors Jumper / Connector Quick Reference Jumpers ConnectorsKBM1 Keyboard & Mouse Connector IDE1 44 pins IDE Connector Connector type PC104 Press FIT 2x20P connector Select IR1 Infrared Connector Pin Mode Strobe AFD PTD0 Error PTD1 Init PTD2 Slin PTD3 GND PTD4 PTD5 COM1/ COM2 Serial Port Connector 17 PDD3 GND PDD4 PDD11 PDD5 PDD12 PDD6 PDD13 PDD7 PDD14 Driver Path Bios Bios Introduction Bios SetupDate Standard Cmos FeaturesTime Drive a / Drive B IDE Primary HDDs / IDE Secondary HDDsVideo Halt On First/ Second Boot Device Advanced Bios FeaturesQuick Power On Self Test Boot Other DeviceSecurity Option Boot Up NumLock StatusCyrix 6x86/MII Cpuid CAS Latency Time Advanced Chipset FeaturesInterleave Select Output display XOR Bit SelectVideo Memory Size Memory Hole At 15M-16MIntegrated Peripherals OnChip IDE Devicev On-Chip IDE ChannelIDE Primary Master/Slave PIO IDE DMA Transfer AccessIDE HDD Block Mode IDE Primary Master/Slave UdmaSuperIO Device Onboard FDC Controller Uart Mode SelectIR Transmission Delay Serial/ Onboard Parallel PortParallel Port Mode UR2 Duplex ModeUse IR Pins EPP Mode SelectDecode I/O Space 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode IODecode I/O Speed 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode Memory Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5Decode I/O Size 0/ 1/ 2/ 3/ 4 Decode Memory Space 0/ 1/ 2Decode Memory Addr / 1/ 2/ 3 Onboard Lan Boot ROMDecode Memory Speed 0/ 1/ 2 Decode Memory Size 0/ 1/ 2 3133&,&RQ¿JXU Wlrqv PNP OS InstalledResources Controlled By Memory Resources IRQ ResourcesPCI/VGA Palette Snoop PC Health Status Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving Bios Beep Sound code list Bios memory mappingAward Bios Post Codes QNRXWVFUHHQ&OH U&026HUURUÀ JBios $XWR&RQ¿JXU WLRQW OH 94h Appendix I/O Port Address Map Address Device DescriptionInterrupt Request Lines IRQ DMA MapMemory Address Map NIC