Diamond Systems LX800 PC/104 user manual Decode Memory Speed 0/ 1/ 2, Decode Memory Addr / 1/ 2/ 3

Page 41

BIOS

Decode Memory Speed 0/ 1/ 2/ 3

It allows you to specify the memory speed of the ISA bus.

Setting: Subtractive Speed, Slow Speed, Medium Speed,

Fast Speed.

Decode Memory Addr. 0/ 1/ 2/ 3 [23:

It allows you to allocate a memory address to the ISA bus. The address may range from 0001 to 0FFF.

Decode Memory Size 0/ 1/ 2/ 3

It allows you to specify the memory size of the ISA bus.

Setting: 16 KB, 32 KB, 64 KB, 128 KB, 256 KB, 512 KB, 1MB, 2MB.

IT8888 DDMA >>>

Suppose that the ISA bus card is required DMA1 & DMA5. Set “DDMA1 Support” & “DDMA5 Support” to “Enabled”.

Onboard Lan Boot ROM

Setting: Enabled, Disabled (Default).

- 38 -

Image 41

Contents Rhodeus-LC Table of Contents Appendix Introduction About User’s Manual Copyright NoticeTechnical Support Replacing the lithium batteryWarranty Ordering Information Packing List 6S L¿ Wlrq BiosBoard Dimensions Introduction Unitmm Installation AMD Geode LX800 CPU 500MHz Block DiagramsJumpers and Connectors Connectors Jumper / Connector Quick Reference JumpersKBM1 Keyboard & Mouse Connector IDE1 44 pins IDE Connector Connector type PC104 Press FIT 2x20P connector Select IR1 Infrared Connector Pin Mode Strobe AFD PTD0 Error PTD1 Init PTD2 Slin PTD3 GND PTD4 PTD5 COM1/ COM2 Serial Port Connector 17 PDD3 GND PDD4 PDD11 PDD5 PDD12 PDD6 PDD13 PDD7 PDD14 Driver Path Bios Bios Setup Bios IntroductionTime Standard Cmos FeaturesDate Video IDE Primary HDDs / IDE Secondary HDDsDrive a / Drive B Halt On Quick Power On Self Test Advanced Bios FeaturesFirst/ Second Boot Device Boot Other DeviceCyrix 6x86/MII Cpuid Boot Up NumLock StatusSecurity Option Interleave Select Advanced Chipset FeaturesCAS Latency Time Video Memory Size XOR Bit SelectOutput display Memory Hole At 15M-16MOnChip IDE Devicev On-Chip IDE Channel Integrated PeripheralsIDE HDD Block Mode IDE DMA Transfer AccessIDE Primary Master/Slave PIO IDE Primary Master/Slave UdmaIR Transmission Delay Uart Mode SelectSuperIO Device Onboard FDC Controller Serial/ Onboard Parallel PortUse IR Pins UR2 Duplex ModeParallel Port Mode EPP Mode SelectDecode I/O Speed 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode IODecode I/O Space 0/ 1/ 2/ 3/ 4 Decode I/O Size 0/ 1/ 2/ 3/ 4 Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5IT8888 ISA Decode Memory Decode Memory Space 0/ 1/ 2Decode Memory Speed 0/ 1/ 2 Onboard Lan Boot ROMDecode Memory Addr / 1/ 2/ 3 Decode Memory Size 0/ 1/ 2Resources Controlled By PNP OS Installed 3133&,&RQ¿JXU Wlrqv PCI/VGA Palette Snoop IRQ ResourcesMemory Resources PC Health Status Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving Bios memory mapping Bios Beep Sound code listQNRXWVFUHHQ&OH U&026HUURUÀ J Award Bios Post CodesBios $XWR&RQ¿JXU WLRQW OH 94h Appendix Address Device Description I/O Port Address MapDMA Map Interrupt Request Lines IRQNIC Memory Address Map