Diamond Systems LX800 PC/104 Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5, Decode I/O Size 0/ 1/ 2/ 3/ 4

Page 40

BIOS

Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5 [15:4]

It allows you to allocate an address to the ISA bus. The address may range from 0001 to 0FFF.

Decode I/O Size 0/ 1/ 2/ 3/ 4/ 5

It allows you to specify the size of the ISA bus.

Setting: 1 Byte, 2 Bytes, 4 Bytes, 8 Bytes, 16 Bytes, 32 Bytes, 64 Bytes, 128 Bytes.

IT8888 ISA Decode Memory >>>

It allows you to use the IT8888 ISA Decode Memory to set the resources for the onboard ISA bus.

Decode Memory Space 0/ 1/ 2/ 3

It allows you to allocate memory resources to the ISA bridge and to enable the function correctly.

Setting: Disabled (Default), Enabled.

- 37 -

Image 40

Contents Rhodeus-LC Table of Contents Appendix Introduction Copyright Notice About User’s ManualReplacing the lithium battery Technical SupportWarranty Packing List Ordering InformationBios 6S L¿ WlrqBoard Dimensions Introduction Unitmm Installation Block Diagrams AMD Geode LX800 CPU 500MHzJumpers and Connectors Jumper / Connector Quick Reference Jumpers ConnectorsKBM1 Keyboard & Mouse Connector IDE1 44 pins IDE Connector Connector type PC104 Press FIT 2x20P connector Select IR1 Infrared Connector Pin Mode Strobe AFD PTD0 Error PTD1 Init PTD2 Slin PTD3 GND PTD4 PTD5 COM1/ COM2 Serial Port Connector 17 PDD3 GND PDD4 PDD11 PDD5 PDD12 PDD6 PDD13 PDD7 PDD14 Driver Path Bios Bios Introduction Bios SetupDate Standard Cmos FeaturesTime Drive a / Drive B IDE Primary HDDs / IDE Secondary HDDsVideo Halt On Advanced Bios Features Quick Power On Self TestFirst/ Second Boot Device Boot Other DeviceSecurity Option Boot Up NumLock StatusCyrix 6x86/MII Cpuid CAS Latency Time Advanced Chipset FeaturesInterleave Select XOR Bit Select Video Memory SizeOutput display Memory Hole At 15M-16MIntegrated Peripherals OnChip IDE Devicev On-Chip IDE ChannelIDE DMA Transfer Access IDE HDD Block ModeIDE Primary Master/Slave PIO IDE Primary Master/Slave UdmaUart Mode Select IR Transmission DelaySuperIO Device Onboard FDC Controller Serial/ Onboard Parallel PortUR2 Duplex Mode Use IR PinsParallel Port Mode EPP Mode SelectDecode I/O Space 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode IODecode I/O Speed 0/ 1/ 2/ 3/ 4 Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5 Decode I/O Size 0/ 1/ 2/ 3/ 4IT8888 ISA Decode Memory Decode Memory Space 0/ 1/ 2Onboard Lan Boot ROM Decode Memory Speed 0/ 1/ 2Decode Memory Addr / 1/ 2/ 3 Decode Memory Size 0/ 1/ 2 3133&,&RQ¿JXU Wlrqv PNP OS InstalledResources Controlled By Memory Resources IRQ ResourcesPCI/VGA Palette Snoop PC Health Status Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving Bios Beep Sound code list Bios memory mappingAward Bios Post Codes QNRXWVFUHHQ&OH U&026HUURUÀ JBios $XWR&RQ¿JXU WLRQW OH 94h Appendix I/O Port Address Map Address Device DescriptionInterrupt Request Lines IRQ DMA MapMemory Address Map NIC