Diamond Systems LX800 PC/104 user manual Select

Page 19

			Installation

JRS1: COM 2 RS-232/422/485 Select (6)
,WF Q HFRQ¿JXUHG&20 WRRSHU WHLQ56		56	RU56 PRGH
Connector type: 2.00mm pitch 2x3 pin header.
Select	1-2	3-4	5-6

RS-232 (Default)	ON	OFF	OFF

RS-422	OFF	ON	OFF

RS-485	OFF	OFF	ON

1

5

2	1
6	5

2	1
6	5

2

6

LLED1: LAN LED indicators (7)

Connector type: 2.54mm pitch 1x4 pin header.

Pin Description

1LAN1_ACTIVE-

2LAN1_ACTIVE+

3LAN1_LINK-

4 LAN1_LINK+

1

JFRT1: Switches and Indicators (8)

It provides connectors for system indicators that provides light indication of the computer activities and switches to change the computer status.

Connector type: 2.54mm pitch 1x8 pin header.
Pin	Description	1
		1
1	RESET+
2	RESET-
3	PWRLED+
4	PWRLED-
5	HDD LED+
6	HDD LED-
7	SPK OUT+

8SPK OUT-

- 16 -

Image 19

Contents Rhodeus-LC Table of Contents Appendix Introduction About User’s Manual Copyright NoticeTechnical Support Replacing the lithium batteryWarranty Ordering Information Packing List 6S L¿ Wlrq BiosBoard Dimensions Introduction Unitmm Installation AMD Geode LX800 CPU 500MHz Block DiagramsJumpers and Connectors Connectors Jumper / Connector Quick Reference JumpersKBM1 Keyboard & Mouse Connector IDE1 44 pins IDE Connector Connector type PC104 Press FIT 2x20P connector Select IR1 Infrared Connector Pin Mode Strobe AFD PTD0 Error PTD1 Init PTD2 Slin PTD3 GND PTD4 PTD5 COM1/ COM2 Serial Port Connector 17 PDD3 GND PDD4 PDD11 PDD5 PDD12 PDD6 PDD13 PDD7 PDD14 Driver Path Bios Bios Setup Bios IntroductionDate Standard Cmos FeaturesTime Drive a / Drive B IDE Primary HDDs / IDE Secondary HDDsVideo Halt On Boot Other Device Advanced Bios FeaturesQuick Power On Self Test First/ Second Boot DeviceSecurity Option Boot Up NumLock StatusCyrix 6x86/MII Cpuid CAS Latency Time Advanced Chipset FeaturesInterleave Select Memory Hole At 15M-16M XOR Bit SelectVideo Memory Size Output displayOnChip IDE Devicev On-Chip IDE Channel Integrated PeripheralsIDE Primary Master/Slave Udma IDE DMA Transfer AccessIDE HDD Block Mode IDE Primary Master/Slave PIOSerial/ Onboard Parallel Port Uart Mode SelectIR Transmission Delay SuperIO Device Onboard FDC ControllerEPP Mode Select UR2 Duplex ModeUse IR Pins Parallel Port ModeDecode I/O Space 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode IODecode I/O Speed 0/ 1/ 2/ 3/ 4 Decode Memory Space 0/ 1/ 2 Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5Decode I/O Size 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode MemoryDecode Memory Size 0/ 1/ 2 Onboard Lan Boot ROMDecode Memory Speed 0/ 1/ 2 Decode Memory Addr / 1/ 2/ 3 3133&,&RQ¿JXU Wlrqv PNP OS InstalledResources Controlled By Memory Resources IRQ ResourcesPCI/VGA Palette Snoop PC Health Status Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving Bios memory mapping Bios Beep Sound code listQNRXWVFUHHQ&OH U&026HUURUÀ J Award Bios Post CodesBios $XWR&RQ¿JXU WLRQW OH 94h Appendix Address Device Description I/O Port Address MapDMA Map Interrupt Request Lines IRQNIC Memory Address Map