Diamond Systems LX800 PC/104 SuperIO Device Onboard FDC Controller, Serial/ Onboard Parallel Port

Page 37

BIOS

SuperIO Device >>>

Onboard FDC Controller

Select “Enabled” if you wish to use it. Select “Disabled” if you don’t wish to use it.

Setting: Disabled, Enabled (Default).

Serial/ Onboard Parallel Port

It allows you to select the onboard serial and parallel ports with their addresses.

Setting:	Serial Port 1	3F8/IRQ4 (Default)
	Serial Port 2	2F8/IRQ3 (Default)
	Parallel Port	378H/IRQ7 (Default)

UART Mode Select

It determines the UART 2 mode in your computer.

Setting: IrDA, ASKIR, Normal (Default).

RxD, TxD Active

Setting: Hi,Hi , Hi,Lo (Default) , Lo,Hi , Lo,Lo.

IR Transmission Delay

Setting: Disabled, Enabled (Default).

- 34 -

Image 37

Contents Rhodeus-LC Table of Contents Appendix Introduction About User’s Manual Copyright NoticeTechnical Support Replacing the lithium batteryWarranty Ordering Information Packing List 6S L¿ Wlrq BiosBoard Dimensions Introduction Unitmm Installation AMD Geode LX800 CPU 500MHz Block DiagramsJumpers and Connectors Connectors Jumper / Connector Quick Reference JumpersKBM1 Keyboard & Mouse Connector IDE1 44 pins IDE Connector Connector type PC104 Press FIT 2x20P connector Select IR1 Infrared Connector Pin Mode Strobe AFD PTD0 Error PTD1 Init PTD2 Slin PTD3 GND PTD4 PTD5 COM1/ COM2 Serial Port Connector 17 PDD3 GND PDD4 PDD11 PDD5 PDD12 PDD6 PDD13 PDD7 PDD14 Driver Path Bios Bios Setup Bios IntroductionDate Standard Cmos FeaturesTime Drive a / Drive B IDE Primary HDDs / IDE Secondary HDDsVideo Halt On Quick Power On Self Test Advanced Bios FeaturesFirst/ Second Boot Device Boot Other DeviceSecurity Option Boot Up NumLock StatusCyrix 6x86/MII Cpuid CAS Latency Time Advanced Chipset FeaturesInterleave Select Video Memory Size XOR Bit SelectOutput display Memory Hole At 15M-16MOnChip IDE Devicev On-Chip IDE Channel Integrated PeripheralsIDE HDD Block Mode IDE DMA Transfer AccessIDE Primary Master/Slave PIO IDE Primary Master/Slave UdmaIR Transmission Delay Uart Mode SelectSuperIO Device Onboard FDC Controller Serial/ Onboard Parallel PortUse IR Pins UR2 Duplex ModeParallel Port Mode EPP Mode SelectDecode I/O Space 0/ 1/ 2/ 3/ 4 IT8888 ISA Decode IODecode I/O Speed 0/ 1/ 2/ 3/ 4 Decode I/O Size 0/ 1/ 2/ 3/ 4 Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5IT8888 ISA Decode Memory Decode Memory Space 0/ 1/ 2Decode Memory Speed 0/ 1/ 2 Onboard Lan Boot ROMDecode Memory Addr / 1/ 2/ 3 Decode Memory Size 0/ 1/ 2 3133&,&RQ¿JXU Wlrqv PNP OS InstalledResources Controlled By Memory Resources IRQ ResourcesPCI/VGA Palette Snoop PC Health Status Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving Bios memory mapping Bios Beep Sound code listQNRXWVFUHHQ&OH U&026HUURUÀ J Award Bios Post CodesBios $XWR&RQ¿JXU WLRQW OH 94h Appendix Address Device Description I/O Port Address MapDMA Map Interrupt Request Lines IRQNIC Memory Address Map