Citizen Systems CLP-8301 user manual EMI Compliance Statement For Canadian Users

Page 3

EMI COMPLIANCE STATEMENT

FOR CANADIAN USERS

This Class A digital apparatus complies with Canadian ICES-003.

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Use shielded cables to connect this device to computers.

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

ETAT DE CONFORMITE EMI A L'USAGE

DES UTILISATEURS CANADIENS

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Cet équipment produit et utilise l'énergie à radiofréquences et s'il n'est pas installé et utilisé correctment, c'esst à dire en accord strict avec les instructions du fabricant, il risque de provoquer des intérferences avec la réception de la radio et de la télévision.

Le présent appareil numérique n'émet pas de bruite radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Cet équipment est conçu pour fournir une protection satisfaisante contre de telles interférences dans une installation résidentielle. Cependant, il n'y a pas de garantie contre les interférences avec les réceptions radio ou télévison, provoquées par la mise en et hors circuit de l'équipment; aussi, il est demandé a l'utilisateur d'essayer de corriger l'interférence par l'une ou plus des mesures suivantes:

Réorienter l'antenne de réception.

Installer l'ordinateur autre part, par égard pour le récepteur.

Brancher l'ordinateur dans une prise de courant différente de façon à ce que l'ordinateur et le récepteur soient branchés sur des circuits différents.

- ii -

Image 3
Contents Barcode Label Printer CLP-8301Page EMI Compliance Statement For Canadian Users Important Safety Instructions Trademark Acknowledgement · Easy operation control panel · Wide media, yet small installation space· Easy access to media and ribbon · Minimum maintenanceTable of Contents Chapter Troubleshooting Configuring Your Printer Using the MenusViii Unpacking ChapterPrinter accessories Examples Safety PrecautionsAvoid unsafe places Power cord Avoid high-humidity areas Loading the media and ribbon Installation precautions Printer main body Names and Functions of Printer PartsPrinter inside Rear and side of printer LCD Display Control panelKey functions in the Ready mode Key functions in the Menu mode Types of media Media Paper and Ribbon¨ Corner-with-a-radius cut tag ¨ Black mark tag¨ Black mark label = LabelMedia size Roll media Loading media paperMedia Paper and Ribbon Path of inward-wound roll media Fanfold media Flange a Loading ribbonMedia Paper and Ribbon Media Paper and Ribbon Media Paper and Ribbon Ribbon tension adjustments Printhead adjustments Media sensor adjustments Media Paper and Ribbon Ribbon guide plate adjustments Media Paper and Ribbon Connecting to a power outlet Power on and Using the Control Panel0000 Turning the printer onReady Ready Mode and Menu ModeNavigating the Menu System Ready mode= Example changing the print density Changing Menu ValuesPermanently Saving Printer Settings = Example producing a test pattern print Producing a Test or Configuration PrintTurning the printer OFF Group Menu Configuring Your Printer Using the MenusDT/T T Setup MenuSystem Setup Menu System Setup MenuSTD/ALT After Print Menu Interface Setup Menu Test Mode Menu Permanently Saving Settings MenuMenu Mode Description STD Configuring Your Printer Using the Menus Items to check in case of trouble TroubleshootingTroubleshooting Jam Error messages and corrective actionsTroubleshooting Printer care MaintenanceCleaning method General specifications SpecificationsXON/XOFF protocol SpecificationsInterfaces Serial interfacePin assignment DTR protocolParallel interface Data Timing chartPrintable area FIX/VR Movable sensorsEnvironmental requirements Printer operating conditions for ensuring print qualityPrinter storage conditions Maintenance Citizen Systems Europe GmbH Mettinger Strasse