Chatsworth Products RIM-600 user manual Selecting Classes

Page 63

Chapter 2: Software

Figure 31: Permissions screen

To configure profiles for Site Administrator or User security levels, select the appropriate Host or Node(s) and click the arrow to copy the Host/Node(s) into the appropriate list. The double arrow

>>will copy all units to the list while the single arrow > will copy just the selected unit to the list. Checking the box “This user can connect remotely via modem” at the bottom of the screen, allows the user listed at the top of the page to dial in to the system using a modem.

In addition to controlling programming access when using the RIM-600 ConsoleView Software, permissions also have an effect during a telephone call. In voice mode the unit will recite only menus and status information for devices that the user has permission to hear. The associated Classes for each user will also control the content of voice reports. The same applies to two-way e-mail. A user can only receive information or send commands if they have the proper permissions and Class associations.

Examples:

1.If a User that has no Permissions on a particular Node, then the user will not be able to receive any Voice or e-mail reports that contain information about that Node.

2.If a User has permissions on a particular Host/Node unit but none of the environmental sensors are in his class, then he will not receive any information about the environmental sensors.

Classes

Clicking the Classes button will bring up the Select Classes screen.

Selecting Classes

The User can choose to receive alarm reports from one or more Classes. The list on the left dis- plays all Available Classes. The list on the right shows Selected Classes for this profile. The Arrow Buttons are used to select or deselect classes. See the following Arrow Button definitions and the following figure:

>Move the highlighted class on the left to the right >> Move all classes on the left to the right (select all)

< Move the highlighted class on the right to the left << Move all classes on the right to the left (deselect all)

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Version Remote Infrastructure Management RIM-600Page Important Safety Instructions Chatsworth Products, Inc Industrial Drive New Bern, NC Fax FCC RequirementsGeneral Requirements for all Automatic Dialers Host only Telephone Consumer Protection Act Host onlyRIM-600 Manual Year Limited Warranty Chatsworth Products, Inc Industrial Drive New Bern, NC Fax Table of Contents RIM-600 Quick Start Guide RIM-600 SoftwareAlarm Logic Software InstallationConfiguring Hosts and Nodes Setting Up An Enterprise Configuring Templates Configuring IP Alarms IP Alarm SetupWeb Configuring User Profiles and Contacts Adding a ProfileHoliday Setup Alarm Message Pop-Ups Deleting a Profile Contacts Adding ContactsSnmp Simple Network Management Protocol GraphsCommunicating with your RIM-600 PowerGate2 Setup via the RIM-600 ConsoleView Software PowerGatePowerGate2 RIM-600 PowerGate Specifications Operating SpecificationsRIM-600 Sensors Water Detection Sensor External Power SensorRoom Humidity Sensor Room Humidity Sensor with displayPassive Infrared Detection Sensor Door SwitchDry Contact Bridge 60051-001 4-20mA BridgeTechnical Support for the RIM-600 Sensors Smoke Detector SensorFeatures IntroductionTechnical Support Front Panel Layout Host Installation and ConfigurationAbout This Manual Physical DescriptionSensor Inputs Rear Panel InstallationAC Power and Battery LEDs ON/OFF SwitchRack Mount Installation Wall Mount InstallationOperating Environment Tabletop Installation Power On Self Test PostConnecting Sensors Network Configuration Enterprise Status Unit Type IP Return to main menu Local Configuration Definitions Replacing the Battery Battery MaintenanceRIM-600 Manual Environmental Monitoring RIM-600 Host SpecificationsOperating Specifications Communications SpecificationsMicrophone Node Installation & ConfigurationBattery Compartment Battery replacement in the Node unit Battery ReplacementWall-mounted Node Unit RIM-600 Node Unit Local Configuration Definitions Node Specifications RIM-600 Quick Start Guide Install Units and Configure Network SettingsInstall Software and Log In to Host Default Username and PasswordConfigure the Unit Properties for the Host and Nodes Configure Input TemplatesConnect Environmental Sensors to Host and Nodes Configure User Profiles and Contacts Configure IP AlarmsRecord and Assign Voice Messages Hardware and Software Requirements Software Installation and Hardware RequirementsSoftware Installation Installing from the CDConfiguring Hosts and Nodes Setting Up An EnterpriseStarting the RIM-600 ConsoleView Software Adding an Enterprise Group Connecting to a HostAdding a Host Deleting a HostSystem Info tab Setting the Unit Properties for the RIM-600 HostAdding a Node Clock settings tabChanging Host Network Settings using ConsoleView Setting the Unit Properties for the NodeDeleting a Node Node Properties Setup Tab Changing Node Network SettingsChannel Setup Configuring Environmental InputsEditing the schedule Channel Setup screenAlarm Class dropdown menu Camera Snapshots on Alarm Alarm Response via the PowerGate, PowerGate2, or CameraRealtime Strip Chart High Sound AlarmsRemoving/Changing a Sensor Environmental Input Alarm LogicTrouble Alarms Configuring TemplatesTemplate Types Configuring IP Alarms IP Alarm SetupProgramming Alarm Parameters IP Schedule screen Alarm Logic IP Alarm Flowchart Removing an IP AlarmSetup Classes Input/Alarm ClassesConfiguring User Profiles and Contacts Configuring User ProfilesAdding a Profile Permissions Master System Site Admin UserSelecting Classes ClassesContacts Deleting a ProfileAdding Contacts Voice Calls Numeric Pager CallsAlphanumeric Pager Calls Schedule Alarm Delivery OptionsFax Calls MailRecording Voice Messages ReconnectingSaving and Loading Programming Recording and Uploading Voice MessagesCustom Voice Manager Holiday List Holiday SetupAlarm Message Pop-Ups Activating Alarm Pop-UpsEnabling Custom Pop-Up Messages Setting Pop-Up Text Location Audible Alarm NotificationEditing Pop-Up Custom Message Smtp Error messages Mail Setup and Two-Way E-Mail CommandsRequesting a Trace Route Two Way E-MailRequesting a Status Report Requesting an IP PingRequesting a PowerGate Outlet Command Requesting a Picture from a CameraRequesting Help Panasonic Configuring a Video CameraAssociating Cameras Graphs WebRemote Web Updating the WebViewing the Remote Web HistoryHistory Options Datalog HistoryViewing History History QuickViewQuerying the History Database with HistoryView Printing Data Exporting Data GraphingArchiving Manually Forcing History DownloadsCopying to the Clipboard Deleting DataManual Datalog Download in progress Updating Firmware

RIM-600 specifications

Chatsworth Products (CPI) has established a reputation for delivering innovative solutions in the field of infrastructure technology. One of their standout products is the RIM-600, a versatile and feature-rich telecommunications rack designed to accommodate various IT equipment needs in data centers and network environments.

The RIM-600 boasts a robust construction, featuring a sturdy steel framework that enhances durability and provides optimal protection for sensitive electronic components. This product is engineered to support a range of IT gear, including servers, network switches, and patch panels, making it an ideal choice for organizations looking to maximize their data center efficiency.

One of the key features of the RIM-600 is its impressive cooling capability. The rack is designed with advanced airflow management in mind. It includes adjustable vertical cable management options that help maintain proper airflow while minimizing cable congestion. This design is crucial for preventing overheating and ensuring reliable performance for all housed equipment, thereby extending the lifespan of critical hardware.

The RIM-600 also incorporates tool-less assembly, simplifying the installation and setup process. This feature is particularly advantageous for IT professionals who require a rapid deployment of systems without cumbersome installation procedures. Furthermore, the rack’s modular design allows for easy customization and scalability, accommodating varying configurations as business needs evolve.

Moreover, the RIM-600 ensures enhanced accessibility with removable side panels and rear doors. This facilitates hassle-free cable access and promotes efficient maintenance practices. The inclusion of integrated grounding provisions ensures that all equipment remains secure and compliant with safety standards.

In terms of scalability, the RIM-600 can support up to 3,000 pounds of equipment, offering ample weight capacity for heavy-duty installations. Its compatibility with popular accessories, including shelving, power distribution units, and cooling solutions, further enhances the rack's utility and flexibility in diverse operational environments.

In summary, the Chatsworth Products RIM-600 is an exceptional telecommunications rack combining durability, cooling efficiency, and ease of installation. Its innovative design and thoughtful features make it a top choice for organizations looking to elevate their data center infrastructure while ensuring equipment protection and optimal performance.
Top Page Image Contents