Chaparral FS2620R manual To enable or disable the alarm

Page 52

FS2620R Rack Model User’s Guide

Table 3-4shows the temperature and voltage thresholds for each alarm and what to do to resolve the problem.

Table 3-4. Alarm thresholds

 

 

Alarm threshold

What to do when the alarm sounds

CPU temperature

✁ Check the Router Administrator software to confirm

Warning—0°C to 4°C and

what the alarm means. See Configuring the Router

91°C to 100°C

on page 3-1.

Shutdown—<0°C and >100°C

✁ Check that the CPU fan is running and is not

 

obstructed.

On-board temperature

✁ You can feel if the fan is running by placing your hand

Warning—0°C to 4°C and

on the rear panel of the router near the power switch.

57°C to 61°C

✁ Check the ambient temperature and lower it, if needed.

Shutdown—<0°C and >61°C

Ambient temperature should be less than 45°C.

 

 

VCC voltage

✁ Check the Router Administrator software to confirm

Warning—5V -5.0% and +6.5%

what the alarm means. See Configuring the Router

Shutdown—5V -6.5% and +10%

on page 3-1.

✁ If it is a warning alarm, let the router continue to

 

 

operate.

 

✁ If it is a shutdown alarm, turn off the power to the

 

router and send it for service.

 

 

12V voltage

✁ Same as above for the VCC voltage.

Warning—12V -10% and +10%

 

Shutdown—12V -20% and +20%

 

 

 

To enable or disable the alarm:

1From the System Menu, select Configuration Menu and press Enter. The Configuration Menu screen displays.

2Select Alarm and press Enter.

The Alarm screen displays. The current setting is marked with an * next to it.

3Select the option you want and press Enter.

The system confirms that the changes are made.

4Press Enter to return to the Configuration Menu.

3-22

Page 51 Page 53
Image 52
Page 51 Page 53
Contents User’s Guide Page Copyright Canadian Compliance Statement Safety Page Contents Address and Device Mapping Reference Documents FS2620R Rack User’s Guide Viii Introduction About this GuideConventions Chaparral FS2620R Router Benefits and FeaturesBold Chaparral FS2620R Router Benefits and Features About Serverless Backup and Restore Specifications PhysicalEnvironmental Unpacking the Router To unpack the routerInstalling the Router Installing on a DesktopInstalling in a Rack To install the FS2620R on a desktopConnecting the Router To install the router in a rackConnecting to the Scsi Channels Rear panel componentsTo connect devices to the Scsi channels Connecting to the Fibre Channel PortTo connect to the Fibre Channel port Connecting to the RS-232 Port To connect to the RS-232 portPowering Up All Devices Connecting to the Ethernet PortTo power up Scsi devices To connect to the Ethernet portUnderstanding the LED Status Lights To make the host FC connectionDescription Color Function Label Router Default Settings Setting Default For more information, seeInstallation Configuration Examples Simple loop configuration exampleMultiple servers on a SAN FC-AL Multiple SANs with fabric FC-SW Combination loop and switch configuration Configuring the Router Accessing the Router Administrator SoftwareFS2620R Rack Model User’s Guide Accessing the Router Administrator Using the Ethernet Port FS2620R Rack Model User’s Guide Configuring the Router’s Network Settings System Configuration Screen Snmp Configuration Screen Restarting the Router Navigating the Router Administrator Software To access the network management systemMenu Tree illustrates the main menu options and sub-options Changing Router Configuration Changing the Screen DisplayConfiguring the FC Host Channels To configure an FC host channel Select Enabled or Disabled and press Enter Changing Router Configuration System confirms that you want to make the changes Changing the Scsi ID Assigned to Each Router Channel To change the Scsi ID assigned to a Scsi channelFS2620R Rack Model User’s Guide Setting the Date and Time To set the router’s dateTo set the router’s time Enabling and Disabling the Alarm Changing the Scan DelayTo change the scan delay To enable or disable the alarm Alarm threshold What to do when the alarm soundsRebooting the Router Restoring the Default SettingsTo restore the default settings Select Restore Defaults and press EnterTo change the mapping mode Changing the Mapping Mode Auto or FixedChanging and Displaying Device Information Select Mapping Mode press Enter Changing Device Addresses FC LUNsSee Changing the Mapping Mode Auto or Fixed on To change the device FC LUNsDisplaying the Devices Connected to the Router Changing Addressing MethodSelect Addressing Method and press Enter To display the devices connected to the router Displaying the FC-to-SCSI Address MapTo display the address map Displaying Router Information Displaying the Event LogTo display one event at a time Select View Event Log and press EnterCapturing the Event Log File To display a full page of eventsDisplaying Hardware and Configuration Information To capture the event log fileGbic To display hardware information only To display hardware and configuration information To display the router’s LUN Displaying the Router’s FC LUNSelect Display Address Map and press Enter Upgrading Firmware To upgrade the router’s firmwareUpgrading the Controller’s Firmware To upgrade the Ethernet card’s firmware Upgrading LAN FirmwareUpgrading Firmware FS2620R Rack Model User’s Guide Problems During Bootup Chaparral Technical SupportFS2620R Rack Model User’s Guide To restore the default configuration Select 2. Clear Configuration and press EnterTerminal Emulator and COM Port Problems SolutionDevice Scsi Channel Problems Router is Not RespondingSetting Up Debug Logging To set up debug loggingUsing the Loader Utility Menu Using the Loader Diagnostics MenuVoltage and Temperature Errors and Warnings FS2620R Rack Model User’s Guide Address and Device Mapping Loop ID to Alpa Mapping DeviceALP 114 115 116 117 118 119 120 121 122 100 123 101 124 102 125 Configuring the Router for TCP/IP Using Address Resolution ProtocolTo use ARP to resolve addresses in Windows Dynamic Host Configuration Protocol ConfigurationArp -s IP address 005013fx-xx-xx Simple Network Management Protocol Configuration To discover which IP address was assigned to the routerFS2620R Rack Model User’s Guide Reference Documents StandardsBooks SBPGlossary G6322/G7324 User’s Guide Glossary G6322/G7324 User’s Guide Index Dhcp Page FS2620R Rack Model User’s Guide TCP/IP FS2620R Rack Model User’s Guide
Top Page Image Contents