Chaparral FS2620R manual Configuring the Router’s Network Settings

Page 35

Accessing the Router Administrator Software

To access the Router Administrator software using the Ethernet port and the Telnet utility:

1At the DOS or UNIX prompt, enter telnet and press Enter.

You should set your Telnet terminal preferences for the router connection.

2Using the Terminal menu, select Preferences.

3Select VT100 Arrows option, VT-100/ANSIemulation, and terminal font. Select OK.

4Enter the IP address or, using the Connect Menu, select the router IP address from the menu (if present). Press Enter.

The Enter Password screen displays.

5Enter your password and press Enter.

There is no default password, just press Enter.

Either the Network Management System Console screen or the Router Administrator screen displays depending on the settings in the System Configuration menu. The default setting takes you directly to the Router Administrator screen. If the Router Administrator Software screen displays, press Enter to display the System Menu. From the System Menu select Configuration Menu. From the Configuration Menu select LAN Config. The the Network Management System Console screen displays. You can configure the router’s network settings from here.

Note: You cannot use RS-232 and Telnet connections at the same time. If a Telnet session is active, you can see the activity through the RS-232 connection, but you cannot make changes to the configuration using the RS-232 connection.

Configuring the Router’s Network Settings

Once you access the router using the Ethernet port, you must configure the router for use. The Network Management System Console screen displays the options available. The following sections briefly describe the options.

3-5

Image 35
Contents User’s Guide Page Copyright Canadian Compliance Statement Safety Page Contents Address and Device Mapping Reference Documents FS2620R Rack User’s Guide Viii About this Guide IntroductionBold Chaparral FS2620R Router Benefits and FeaturesConventions Chaparral FS2620R Router Benefits and Features About Serverless Backup and Restore Physical SpecificationsEnvironmental To unpack the router Unpacking the RouterTo install the FS2620R on a desktop Installing the RouterInstalling on a Desktop Installing in a RackTo install the router in a rack Connecting the RouterRear panel components Connecting to the Scsi ChannelsTo connect to the Fibre Channel port Connecting to the Fibre Channel PortTo connect devices to the Scsi channels To connect to the RS-232 port Connecting to the RS-232 PortTo connect to the Ethernet port Powering Up All DevicesConnecting to the Ethernet Port To power up Scsi devicesTo make the host FC connection Understanding the LED Status LightsDescription Color Function Label Setting Default For more information, see Router Default SettingsSimple loop configuration example Installation Configuration ExamplesMultiple servers on a SAN FC-AL Multiple SANs with fabric FC-SW Combination loop and switch configuration Accessing the Router Administrator Software Configuring the RouterFS2620R Rack Model User’s Guide Accessing the Router Administrator Using the Ethernet Port FS2620R Rack Model User’s Guide Configuring the Router’s Network Settings System Configuration Screen Snmp Configuration Screen Restarting the Router To access the network management system Navigating the Router Administrator SoftwareMenu Tree illustrates the main menu options and sub-options Changing the Screen Display Changing Router ConfigurationConfiguring the FC Host Channels To configure an FC host channel Select Enabled or Disabled and press Enter Changing Router Configuration System confirms that you want to make the changes To change the Scsi ID assigned to a Scsi channel Changing the Scsi ID Assigned to Each Router ChannelFS2620R Rack Model User’s Guide To set the router’s date Setting the Date and TimeTo set the router’s time To change the scan delay Changing the Scan DelayEnabling and Disabling the Alarm Alarm threshold What to do when the alarm sounds To enable or disable the alarmSelect Restore Defaults and press Enter Rebooting the RouterRestoring the Default Settings To restore the default settingsChanging and Displaying Device Information Changing the Mapping Mode Auto or FixedTo change the mapping mode Changing Device Addresses FC LUNs Select Mapping Mode press EnterTo change the device FC LUNs See Changing the Mapping Mode Auto or Fixed onSelect Addressing Method and press Enter Changing Addressing MethodDisplaying the Devices Connected to the Router To display the address map Displaying the FC-to-SCSI Address MapTo display the devices connected to the router Displaying the Event Log Displaying Router InformationSelect View Event Log and press Enter To display one event at a timeTo display a full page of events Capturing the Event Log FileTo capture the event log file Displaying Hardware and Configuration InformationGbic To display hardware information only To display hardware and configuration information Select Display Address Map and press Enter Displaying the Router’s FC LUNTo display the router’s LUN Upgrading the Controller’s Firmware To upgrade the router’s firmwareUpgrading Firmware Upgrading LAN Firmware To upgrade the Ethernet card’s firmwareUpgrading Firmware FS2620R Rack Model User’s Guide Chaparral Technical Support Problems During BootupFS2620R Rack Model User’s Guide Select 2. Clear Configuration and press Enter To restore the default configurationSolution Terminal Emulator and COM Port ProblemsRouter is Not Responding Device Scsi Channel ProblemsTo set up debug logging Setting Up Debug LoggingVoltage and Temperature Errors and Warnings Using the Loader Diagnostics MenuUsing the Loader Utility Menu FS2620R Rack Model User’s Guide Address and Device Mapping Device Loop ID to Alpa MappingALP 114 115 116 117 118 119 120 121 122 100 123 101 124 102 125 Using Address Resolution Protocol Configuring the Router for TCP/IPArp -s IP address 005013fx-xx-xx Dynamic Host Configuration Protocol ConfigurationTo use ARP to resolve addresses in Windows To discover which IP address was assigned to the router Simple Network Management Protocol ConfigurationFS2620R Rack Model User’s Guide Standards Reference DocumentsSBP BooksGlossary G6322/G7324 User’s Guide Glossary G6322/G7324 User’s Guide Index Dhcp Page FS2620R Rack Model User’s Guide TCP/IP FS2620R Rack Model User’s Guide