Chaparral FS2620R manual Tcp/Ip

Page 97

Address Mapping 3-24Alarm 3-22

Change Address Map 3-26Channel 3-18

Channel Configuration 3-17

Configuration Menu 3-13Display Address Map 3-26, 3-29Display Devices 3-28Enabled/Disabled 3-14

Event Log 3-30Event Log Menu 3-30Flash Utility 3-38

Hardware Information 3-34, 4-6Host Configuration 3-14initial Router Administrator 3-2Link Speed 3-15

Loop ID 3-15Mapping Mode 3-25navigating in 3-9Restore Defaults 3-23Router LUN 3-16Scan Configuration 3-21Set Date 3-19

Set Date/Time 3-19Set Time 3-20System Menu 3-2, 3-8Utilities Menu 3-34, 4-6

SCSI channels

changing mapping mode 3-24connecting to 2-4

LVD 2-4problems with 4-5single-ended narrow 2-4Ultra2 wide 2-4

SCSI devices

changing addresses of 3-25, 3-27changing FC LUNs of 3-25, 3-27displaying 3-27, 3-28

SCSI ID, changing for router 3-17serial port 2-6

connecting to 2-6problems with 4-4serverless backup 1-4Set Date screen 3-19

Set Date/Time screen 3-19Set Time screen 3-20

setting

FC channel speed 3-13setting up the router 3-1settings

for the RS-232 port 2-6settings for 2-6, 3-12shutting down the router 3-23SNMP Configuration screen 3-7SNMP trap 3-8

SOFT setting 3-12software

accessing to configure the router 3-1navigating in 3-9

specifications 1-5speed

setting for FC channels 3-13ST light 2-8

status lights 2-8support 4-1

System Configuration screen 3-6System Menu 3-2, 3-8

T

table, installing the router on 2-2

TCP/IP

configuring the router B-1TCP/IP Configuration screen 3-6technical support 4-1

Telnet

accessing Router Administrator software 3-5temperature, alarm thresholds for 3-22terminal

screen problems 4-4terminal emulator software 3-1terminal emulator, problems with 4-4terminal screen problems 4-4

time, changing for router 3-19topology

Auto Detection setting 3-12LOOP setting 3-12POINT-TO-POINT setting 3-12selecting 3-12

troubleshooting COM port 4-4

device SCSI channel problems 4-5

I-5

Image 97

Contents User’s Guide Page Copyright Canadian Compliance Statement Safety Page Contents Address and Device Mapping Reference Documents FS2620R Rack User’s Guide Viii About this Guide IntroductionConventions Chaparral FS2620R Router Benefits and FeaturesBold Chaparral FS2620R Router Benefits and Features About Serverless Backup and Restore Physical SpecificationsEnvironmental To unpack the router Unpacking the RouterInstalling on a Desktop Installing the RouterInstalling in a Rack To install the FS2620R on a desktopTo install the router in a rack Connecting the RouterRear panel components Connecting to the Scsi ChannelsTo connect devices to the Scsi channels Connecting to the Fibre Channel PortTo connect to the Fibre Channel port To connect to the RS-232 port Connecting to the RS-232 PortConnecting to the Ethernet Port Powering Up All DevicesTo power up Scsi devices To connect to the Ethernet portTo make the host FC connection Understanding the LED Status LightsDescription Color Function Label Setting Default For more information, see Router Default SettingsSimple loop configuration example Installation Configuration ExamplesMultiple servers on a SAN FC-AL Multiple SANs with fabric FC-SW Combination loop and switch configuration Accessing the Router Administrator Software Configuring the RouterFS2620R Rack Model User’s Guide Accessing the Router Administrator Using the Ethernet Port FS2620R Rack Model User’s Guide Configuring the Router’s Network Settings System Configuration Screen Snmp Configuration Screen Restarting the Router To access the network management system Navigating the Router Administrator SoftwareMenu Tree illustrates the main menu options and sub-options Changing the Screen Display Changing Router ConfigurationConfiguring the FC Host Channels To configure an FC host channel Select Enabled or Disabled and press Enter Changing Router Configuration System confirms that you want to make the changes To change the Scsi ID assigned to a Scsi channel Changing the Scsi ID Assigned to Each Router ChannelFS2620R Rack Model User’s Guide To set the router’s date Setting the Date and TimeTo set the router’s time Enabling and Disabling the Alarm Changing the Scan DelayTo change the scan delay Alarm threshold What to do when the alarm sounds To enable or disable the alarmRestoring the Default Settings Rebooting the RouterTo restore the default settings Select Restore Defaults and press EnterTo change the mapping mode Changing the Mapping Mode Auto or FixedChanging and Displaying Device Information Changing Device Addresses FC LUNs Select Mapping Mode press EnterTo change the device FC LUNs See Changing the Mapping Mode Auto or Fixed onDisplaying the Devices Connected to the Router Changing Addressing MethodSelect Addressing Method and press Enter To display the devices connected to the router Displaying the FC-to-SCSI Address MapTo display the address map Displaying the Event Log Displaying Router InformationSelect View Event Log and press Enter To display one event at a timeTo display a full page of events Capturing the Event Log FileTo capture the event log file Displaying Hardware and Configuration InformationGbic To display hardware information only To display hardware and configuration information To display the router’s LUN Displaying the Router’s FC LUNSelect Display Address Map and press Enter Upgrading Firmware To upgrade the router’s firmwareUpgrading the Controller’s Firmware Upgrading LAN Firmware To upgrade the Ethernet card’s firmwareUpgrading Firmware FS2620R Rack Model User’s Guide Chaparral Technical Support Problems During BootupFS2620R Rack Model User’s Guide Select 2. Clear Configuration and press Enter To restore the default configurationSolution Terminal Emulator and COM Port ProblemsRouter is Not Responding Device Scsi Channel ProblemsTo set up debug logging Setting Up Debug LoggingUsing the Loader Utility Menu Using the Loader Diagnostics MenuVoltage and Temperature Errors and Warnings FS2620R Rack Model User’s Guide Address and Device Mapping Device Loop ID to Alpa MappingALP 114 115 116 117 118 119 120 121 122 100 123 101 124 102 125 Using Address Resolution Protocol Configuring the Router for TCP/IPTo use ARP to resolve addresses in Windows Dynamic Host Configuration Protocol ConfigurationArp -s IP address 005013fx-xx-xx To discover which IP address was assigned to the router Simple Network Management Protocol ConfigurationFS2620R Rack Model User’s Guide Standards Reference DocumentsSBP BooksGlossary G6322/G7324 User’s Guide Glossary G6322/G7324 User’s Guide Index Dhcp Page FS2620R Rack Model User’s Guide TCP/IP FS2620R Rack Model User’s Guide