Carrier D2-3466-2 instruction manual For Carrier Drives

Page 15

CHAPTER 4

Identifying Parameter Defaults

For Carrier Drives

Use the following table to identify and set the parameter defaults for Carrier drives.

Important: Setting P.050 (Restore Defaults) to ON will restore the drive to Reliance defaults, not Carrier defaults. If this has been done, set the following parameters to restore Carrier defaults.

Parameter No.

Parameter Name

Setting

 

 

 

 

P.000

Control Source

rE

 

 

 

 

P.001

Accel Time 1

8

 

 

 

 

 

P.002

Decel Time 1

20

 

 

 

 

 

P.003

Minimum Speed

0.5

 

 

 

 

 

P.004

Maximum Speed

Job-specific (50 or 60)

 

 

 

 

P.005

Current Limit

110

 

 

 

 

 

P.0091

Terminal Strip Analog Input Offset

-10

 

P.0101

Terminal Strip Analog Input Gain

0.99 (50LR4060, 64LR4060)

 

 

1.030 (41LR4060)

P.011

Terminal Strip Analog Input Configure

4

 

 

 

 

 

P.013

Output Relay Configuration

2

 

 

 

 

 

P.027

Forward/Reverse Configuration

1

 

 

 

 

 

P.028

Speed Display Scaling

Job-specific

 

 

 

 

P.043

Fault Auto Reset Attempts

10

 

 

 

 

 

P.044

Fault Auto Reset Time

30

 

 

 

 

 

P.052

AUTO/MAN Key Disable

ON

 

 

 

 

H.000

Motor Nameplate Volts

Job-specific

H.001

Motor Nameplate Base Frequency

Job-specific

 

 

 

H.002

Motor Nameplate Amps

1.03 x Motor Nameplate Amps

 

 

 

H.021

AC Line Volts

Job-specific

 

 

 

H.022

Overfrequency Limit

Job-specific (57 or 69)

 

 

 

 

r.001

Analog Output 1 Source

4

 

r.0021

Analog Output 1 Offset

60 (50LR4060, 64LR4060)

 

 

135 (41LR4060)

r.0031

Analog Output 1 Gain

0.505 (50LR4060, 64LR4060)

 

 

0.503 (41LR4060)

r.035

Relay Output 1 (NO) Configuration

5

 

 

 

 

 

r.036

Relay Output 2 (NO/NC) Configuration

2

 

 

 

 

 

r.037

Relay Output 3 (NO/NC) Configuration

1

 

 

 

 

 

r.046

Relay Output 3 Delay Time

-999

 

 

 

 

 

r.050

Speed Detection Level 1

35

 

 

 

 

 

1These parameters must be tuned or calibrated per the VFD Control Verification procedures (running and non-running) found in the Carrier 19XR/XRV Start-Up, Operation, and Maintenance Instructions on pages 59-60.

For job-specific parameters, refer to the 19XR, XRV Start-Up, Operation, and Maintenance Instructions manual (531-982) for further instructions. For descriptions of all parameters, refer to the LiquiFlo Software Start-Up and Reference manual (D2-3410).

Identifying Parameter Defaults For Carrier Drives

4-1

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Carrier VFD Quick Reference Page Page Page Page Page Contents Carrier VFD Quick Reference Getting Assistance from Reliance Electric Required PublicationsCarrier VFD Quick Reference Replace with 2.fm 11 X 17 Z-fold Carrier VFD Quick Reference Monitor Mode Carrier VFD Quick Reference For Carrier Drives Carrier VFD Quick Reference Record the following nameplate information Record the following job informationCarrier VFD Quick Reference Verifying That DC Bus Capacitors Are Discharged Test Equipment Needed To TroubleshootPOS NEG TP1 TP2 Initial DC Bus Checking the Power Modules and Motor with Input Power Off Igbt Error Log Troubleshooting the Drive Using Error CodesAlarm Codes Fault CodesAlarm Code Description Alarm Cause Corrective Action Identifying Alarm Codes and RecoveringFault Code Description Fault Cause Corrective Action Identifying Fault Codes and RecoveringIPL OPL Input Ground Fault Excessive Asymmetrical Bus WhenSlow Ramp Rate of DC Bus DC Carrier VFD Quick Reference Troubleshooting the Drive Code Fault Description Fault Cause Corrective Action Identifying Fatal Fault Codes and RecoveringIndentifying PMC Board Fault Codes and Recovering Resetting a Checksum CHS FaultStatus of LEDs Fault Description Corrective Action Model Amps Code Number Technical Writing Internal Use DIFPage Page Publication D2-3466-2 May 2005 -- Supercedes D2-3466-1 June
Top Page Image Contents