Operating Instructions | Model SN258K |
General Safety Information (Continued)
reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury.
●Use only a pressure- regulated compressed
air source to limit the air pressure supplied to the tool. The regu-
lated pressure must
not exceed 100 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury.
● Never use gasoline
or other flammable liquids to clean the tool. Never use the
tool in the presence
of flammable liquids or gases. Vapors could ignite by a spark and cause an explosion which will result in death or serious personal injury.
● Always remain in a firmly balanced position when using or handling the tool.
●Do not remove, tamper with, or
otherwise cause the Work Contact Element (WCE) or
trigger to become
inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result.
●Do not touch the
trigger unless dri- ving fasteners. Never attach air
line to tool or carry tool while
touching the trigger. The tool could eject a fastener which will result in death or serious personal injury.
Warning indicates
! WARNING a potentially hazardous situation which, if not avoid- ed, COULD result in death or
serious injury.
●Always discon- nect the tool
from the power source when unattended, performing any
maintenance or repair, clearing a jam, or moving the tool to a new location. Always reconnect the air line BEFORE loading any fasteners. Do not load the tool with fasteners when either the trigger is depressed or the Work Contact Element (WCE) is engaged. The tool could eject a fastener causing death or serious personal injury.
●Always fit tool with a fitting or
hose coupling on or near the
tool in such a manner that all
compressed air in the tool is dis- charged at the time the fitting or hose coupling is disconnected. Do not use a check valve or any other fit- ting which allows air to remain in the tool. Death or serious personal injury could occur.
●Never place hands or any other body parts in the fastener discharge area of the tool. The tool might eject a fas- tener and could result
in death or serious personal injury.
●Never carry the
tool by the air
hose or pull the hose to move the
tool or a compres- sor. Keep hoses
away from heat,
oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool dam- age could occur.
●Always assume the tool contains fas- teners. Respect the tool as a work- ing implement; no horseplay. Always keep others at a safe dis- tance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fas- teners or not. Accidental triggering of the tool could result in death or serious personal injury.
●Do not drive a
fastener on top of other fasteners. The fastener could glance and cause death or a serious puncture wound.
●Do not operate
or allow anyone else to operate
the tool if any warnings or warning labels
are not legible. Warnings or warning
Stapler Components And Specifications | Warning Labels |
Cap Exhaust |
|
• REQUIRES: .80 SCFM with 10 staples |
|
per minute @ 90 psi |
|
• AIR INLET: 1/4” NPT | Magazine |
• STAPLE SIZE RANGE: 3/8” to 1” | Trigger |
•MAGAZINE CAPACITY:
100 Staples per load, 18 gauge |
| Latch |
• WEIGHT: 2 lbs., 9 oz. |
|
|
• LENGTH: 9” |
|
|
• HEIGHT: 7” |
|
|
• MAXIMUM PRESSURE: 100 psi |
|
|
• PRESSURE RANGE: 50 - 100 psi | Work Contact | Staple Loading Area |
| Element (WCE) |
|
|
| Staple Discharge Area |
www.chpower.com |
|
|
2