Specifications, 7011/I-7011D | B&B Electronics specs

1.3 Specifications

I-7011/I-7011D
Analog Input		Logic Level 0 : +1V max
Input Channel :	1	Logic Level 1 : +3.5 to 30V
Input Type :		Event Counter
mV, V, mA(with external		Max Input Frequency : 50 Hz
125 ohms resistor)		Min. Pulse Width : 1 mS
Thermocouple : Type J, K,		Displayed LED
T, E, R, S, B, N, C		4½ digits (for I-7011D)
Sampling Rate :		Power Supply
10 Samples/Second		Input : +10 to +30 VDC
Bandwidth : 5.24 Hz		Consumption :
Accuracy : ±0.05%		0.9W for I-7011
Zero Drift : 0.5µV/°C		1.5W for I-7011D
Span Drift : 25ppm/°C
CMR@50/60Hz : 150dB
NMR@50/60Hz : 100dB
Input Impedance : 20M Ohms

Isolation : 3000VDC

Digital Output

2 channel

Open Collector to 30V Output Load : sink 30mA max Power Dissipation : 300mW

Digital Input 1 channel

I-7011, I-7018 User Manual

Rev:B1.0

Page 8

Image 8

B&B Electronics user manual Specifications, 7011/I-7011D

Contents

Trademark WarrantyCopyright Table of Contents @AADOData High/Low Alarm Introduction More Information Pin Assignment RevB1.0 Specifications 7011/I-7011D 7011P/I-7011PD 7018 7018P Block Diagram Wire Connection Page Quick Start Default SettingJumper Setting Calibration Don’t Perform Calibrate Until You Really Understand Data Format Setting FF Configuration TablesBaudrate Setting CC Analog Input Type Setting TT Analog input type and data format table Type Input Range Data Format +F.S Zero Code RevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 Related Command Syntax %AANNTTCCFFCHKcrAACHKcr ?AACHKcr Syntax #**CHKcr Example #AA Syntax #AACHKcr Syntax #AANCHKcr Response Valid Command DataCHKcr Invalid Command ?AACHKcr#AAN $AA0 Syntax $AA0CHKcr $AA1 Syntax $AA1CHKcr $AA2 Syntax $AA2CHKcrAATTCCFFCHKcr FF data format of module reference Sec.1.10 Example $AA3 Syntax $AA3CHKcr $AA4 Syntax $AA4CHKcrAASDataCHKcr Data synchronized data, format reference Sec.1.10 Example 10 $AA5VV Syntax $AA5VVCHKcr AAVVCHKcr 11 $AA6Syntax $AA6CHKcr AAVCHKcr 12 $AA8Syntax $AA8CHKcr 13 $AA8V Syntax $AA8VCHKcr Related Command Sec.2.8 $AA3 14 $AA9DataSyntax $AA9DataCHKcr AA address of response module 00 to FF Example AASCHKcr 15 $AABSyntax $AABCHKcr AADataCHKcr 16 $AAFSyntax $AAFCHKcr 17 $AAM Syntax $AAMCHKcr 18 $AAZData Syntax $AAZDataCHKcr Syntax ~AAODataCHKcr Read address 01 module name, return 7018. Related Command19 ~AAOData Related Topic 20 ~AAEVSyntax ~AAEVCHKcr 21 @AADI Syntax @AADICHKcrAASOOIICHKcr Level. Example High 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr 24 @AAHIData 25 @AALOData Syntax @AADACHKcr Related Command Sec.2.23 @AAEAT Related Topic26 @AADA 27 @AACA Syntax @AACACHKcr Syntax @AARHCHKcr Read address 01 high alarm, return +2.5000. Related Command28 @AARH 29 @AARL Syntax @AARECHKcr Read address 01 event counter, return 1234. Related Command30 @AARE 31 @AACE Syntax @AACECHKcr 32 ~ Description Host OKSyntax ~**CHKcr Response No response. Example Host watchdog timeout flag, 0=Clear, 1=Set Example 33 ~AA0Syntax ~AA0CHKcr AASSCHKcr 34 ~AA1 Syntax ~AA1CHKcr 35 ~AA2 Syntax ~AA2CHKcr 36 ~AA3EVV Syntax ~AA3EVVCHKcr 37 ~AA4 Syntax ~AA4CHKcrAAPPSSCHKcr SS Safe Value, data format is same as PP Example 38 ~AA5PPSS Syntax ~AA5PPSSCHKcr INIT* pin Operation Module Status Dual Watchdog Operation Digital Input and Event CounterDigital Output Dual Watchdog = Module Watchdog + Host Watchdog High/Low Alarm Thermocouple Measurement

1.3 Specifications

I-7011/I-7011D

Event Counter

Power Supply

Rev:B1.0