Configuration Tables | B&B Electronics I-7011 instruction

1.10 Configuration Tables

Configuration Table of I-7011/11D/11P/11PD/18/18P :

Baudrate Setting (CC)

Analog Input Type Setting (TT)

T.C Type L and M for I-7011P/11PD/18P only.

Data Format Setting (FF)

*1	: Filter Select : 0 = 60Hz rejection
		1 = 50Hz rejection
*2	: Checksum Bit : 0=Disable, 1=Enable
*3	: 00	= Engineer Unit Format
	01	= Percent Format
	10	= 2’s Complement HEX Format

16		I-7011, I-7018 User Manual	Rev:B1.0

Page 16

Image 16

B&B Electronics I-7011 Configuration Tables, Baudrate Setting CC Analog Input Type Setting TT, Data Format Setting FF

Contents

Copyright WarrantyTrademark Table of Contents @AADOData High/Low Alarm Introduction More Information Pin Assignment RevB1.0 Specifications 7011/I-7011D 7011P/I-7011PD 7018 7018P Block Diagram Wire Connection Page Jumper Setting Default SettingQuick Start Calibration Don’t Perform Calibrate Until You Really Understand Baudrate Setting CC Analog Input Type Setting TT Configuration TablesData Format Setting FF Analog input type and data format table Type Input Range Data Format +F.S Zero Code RevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 Related Command Syntax %AANNTTCCFFCHKcrAACHKcr ?AACHKcr Syntax #**CHKcr Example #AA Syntax #AACHKcr #AAN Response Valid Command DataCHKcr Invalid Command ?AACHKcrSyntax #AANCHKcr $AA0 Syntax $AA0CHKcr $AA1 Syntax $AA1CHKcr $AA2 Syntax $AA2CHKcrAATTCCFFCHKcr FF data format of module reference Sec.1.10 Example $AA3 Syntax $AA3CHKcr $AA4 Syntax $AA4CHKcrAASDataCHKcr Data synchronized data, format reference Sec.1.10 Example 10 $AA5VV Syntax $AA5VVCHKcr Syntax $AA6CHKcr 11 $AA6AAVVCHKcr Syntax $AA8CHKcr 12 $AA8AAVCHKcr 13 $AA8V Syntax $AA8VCHKcr Related Command Sec.2.8 $AA3 14 $AA9DataSyntax $AA9DataCHKcr AA address of response module 00 to FF Example Syntax $AABCHKcr 15 $AABAASCHKcr Syntax $AAFCHKcr 16 $AAFAADataCHKcr 17 $AAM Syntax $AAMCHKcr 18 $AAZData Syntax $AAZDataCHKcr 19 ~AAOData Read address 01 module name, return 7018. Related CommandSyntax ~AAODataCHKcr Syntax ~AAEVCHKcr 20 ~AAEVRelated Topic 21 @AADI Syntax @AADICHKcrAASOOIICHKcr Level. Example High 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr 24 @AAHIData 25 @AALOData 26 @AADA Related Command Sec.2.23 @AAEAT Related TopicSyntax @AADACHKcr 27 @AACA Syntax @AACACHKcr 28 @AARH Read address 01 high alarm, return +2.5000. Related CommandSyntax @AARHCHKcr 29 @AARL 30 @AARE Read address 01 event counter, return 1234. Related CommandSyntax @AARECHKcr 31 @AACE Syntax @AACECHKcr 32 ~ Description Host OKSyntax ~**CHKcr Response No response. Example Host watchdog timeout flag, 0=Clear, 1=Set Example 33 ~AA0Syntax ~AA0CHKcr AASSCHKcr 34 ~AA1 Syntax ~AA1CHKcr 35 ~AA2 Syntax ~AA2CHKcr 36 ~AA3EVV Syntax ~AA3EVVCHKcr 37 ~AA4 Syntax ~AA4CHKcrAAPPSSCHKcr SS Safe Value, data format is same as PP Example 38 ~AA5PPSS Syntax ~AA5PPSSCHKcr INIT* pin Operation Module Status Dual Watchdog Operation Digital Input and Event CounterDigital Output Dual Watchdog = Module Watchdog + Host Watchdog High/Low Alarm Thermocouple Measurement

1.10 Configuration Tables

Baudrate Setting (CC)

Analog Input Type Setting (TT)

Data Format Setting (FF)

Rev:B1.0