7018P | B&B Electronics I-7011 manual

I-7018

Analog Input

Input Channel :

8 differential or 6 differen- tial and 2 single-ended. Jumper select.

Input Type :

mV, V, mA(with external 125 ohms resistor) Thermocouple : Type J, K, T, E, R, S, B, N, C

Sampling Rate :

10Samples/Second

Bandwidth : 15.7 Hz

Accuracy : ±0.1%

Zero Drift : 0.5µV/°C

Span Drift : 25ppm/°C

CMR@50/60Hz : 150dB

NMR@50/60Hz : 100dB

Input Impedance : 20M Ohms

Overvoltage Protection : ±35V

Isolation : 3000VDC

Power Supply

Input : +10 to +30 VDC

I-7018P

Analog Input

Input Channel :

8 differential or 6 differen- tial and 2 single-ended. Jumper select.

Analog Input Type :

mV, V, mA(with external 125 ohms resistor) Thermocouple : Type J, K, T, E, R, S, B, N, C, L, M

Sampling Rate :

10Samples/Second

Bandwidth : 15.7 Hz

Accuracy : ±0.1%

Zero Drift : 0.5µV/°C

Span Drift : 25ppm/°C

CMR@50/60Hz : 150dB

NMR@50/60Hz : 100dB

Input Impedance : 20M Ohms

Overvoltage Protection : ±35V

Isolation : 3000VDC

Power Supply

Input : +10 to +30 VDC


Consumption : 1.0W		Consumption : 1.0W
10	I-7011, I-7018 User Manual		Rev:B1.0

Image 10

B&B Electronics I-7011 user manual 7018P

Contents

Copyright WarrantyTrademark Table of Contents @AADOData High/Low Alarm Introduction More Information Pin Assignment RevB1.0 Specifications 7011/I-7011D 7011P/I-7011PD 7018 7018P Block Diagram Wire Connection Page Jumper Setting Default SettingQuick Start Calibration Don’t Perform Calibrate Until You Really Understand Baudrate Setting CC Analog Input Type Setting TT Configuration TablesData Format Setting FF Analog input type and data format table Type Input Range Data Format +F.S Zero Code RevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 AACHKcr Related CommandSyntax %AANNTTCCFFCHKcr ?AACHKcr Syntax #**CHKcr Example #AA Syntax #AACHKcr #AAN Response Valid Command DataCHKcr Invalid Command ?AACHKcrSyntax #AANCHKcr $AA0 Syntax $AA0CHKcr $AA1 Syntax $AA1CHKcr AATTCCFFCHKcr $AA2Syntax $AA2CHKcr FF data format of module reference Sec.1.10 Example $AA3 Syntax $AA3CHKcr AASDataCHKcr $AA4Syntax $AA4CHKcr Data synchronized data, format reference Sec.1.10 Example 10 $AA5VV Syntax $AA5VVCHKcr Syntax $AA6CHKcr 11 $AA6AAVVCHKcr Syntax $AA8CHKcr 12 $AA8AAVCHKcr 13 $AA8V Syntax $AA8VCHKcr Syntax $AA9DataCHKcr Related Command Sec.2.8 $AA314 $AA9Data AA address of response module 00 to FF Example Syntax $AABCHKcr 15 $AABAASCHKcr Syntax $AAFCHKcr 16 $AAFAADataCHKcr 17 $AAM Syntax $AAMCHKcr 18 $AAZData Syntax $AAZDataCHKcr 19 ~AAOData Read address 01 module name, return 7018. Related CommandSyntax ~AAODataCHKcr Syntax ~AAEVCHKcr 20 ~AAEVRelated Topic AASOOIICHKcr 21 @AADISyntax @AADICHKcr Level. Example High 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr 24 @AAHIData 25 @AALOData 26 @AADA Related Command Sec.2.23 @AAEAT Related TopicSyntax @AADACHKcr 27 @AACA Syntax @AACACHKcr 28 @AARH Read address 01 high alarm, return +2.5000. Related CommandSyntax @AARHCHKcr 29 @AARL 30 @AARE Read address 01 event counter, return 1234. Related CommandSyntax @AARECHKcr 31 @AACE Syntax @AACECHKcr Syntax ~**CHKcr 32 ~Description Host OK Response No response. Example Syntax ~AA0CHKcr Host watchdog timeout flag, 0=Clear, 1=Set Example33 ~AA0 AASSCHKcr 34 ~AA1 Syntax ~AA1CHKcr 35 ~AA2 Syntax ~AA2CHKcr 36 ~AA3EVV Syntax ~AA3EVVCHKcr AAPPSSCHKcr 37 ~AA4Syntax ~AA4CHKcr SS Safe Value, data format is same as PP Example 38 ~AA5PPSS Syntax ~AA5PPSSCHKcr INIT* pin Operation Module Status Digital Output Dual Watchdog OperationDigital Input and Event Counter Dual Watchdog = Module Watchdog + Host Watchdog High/Low Alarm Thermocouple Measurement