Quick Start, Default Setting | B&B Electronics I-7011 guide

1.6 Quick Start

Refer to “I-7000 Bus Converter User Manual” and “Get-

ting Start” for more detail.

1.7 Default Setting

Default setting for I-7011/11D/11P/11PD/18/18P :

zAddress : 01

zAnalog Input Type : Type 05, -2.5 to +2.5 V

zBaudrate : 9600 bps

zChecksum disable, 60Hz rejection, engineer unit format

zI-7018/18P set as INIT* mode, and the analog input is 6 dif- ferential and 2 single-ended.

1.8 Jumper Setting

I-7018/18P : Jumper JP1 for select the pin INIT*/Vin 7- Select 8 differential mode, the pin INIT*/Vin7- is set to Vin7-

Select INIT* mode, the pin INIT*/Vin7- is set to INIT*

I-7011, I-7018 User Manual

Rev:B1.0

Page 14

Image 14

B&B Electronics I-7011 user manual Quick Start, Default Setting, Jumper Setting

Contents

Trademark WarrantyCopyright Table of Contents @AADOData High/Low Alarm Introduction More Information Pin Assignment RevB1.0 Specifications 7011/I-7011D 7011P/I-7011PD 7018 7018P Block Diagram Wire Connection Page Quick Start Default SettingJumper Setting Calibration Don’t Perform Calibrate Until You Really Understand Data Format Setting FF Configuration TablesBaudrate Setting CC Analog Input Type Setting TT Analog input type and data format table Type Input Range Data Format +F.S Zero Code RevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 AACHKcr Related CommandSyntax %AANNTTCCFFCHKcr ?AACHKcr Syntax #**CHKcr Example #AA Syntax #AACHKcr Syntax #AANCHKcr Response Valid Command DataCHKcr Invalid Command ?AACHKcr#AAN $AA0 Syntax $AA0CHKcr $AA1 Syntax $AA1CHKcr AATTCCFFCHKcr $AA2Syntax $AA2CHKcr FF data format of module reference Sec.1.10 Example $AA3 Syntax $AA3CHKcr AASDataCHKcr $AA4Syntax $AA4CHKcr Data synchronized data, format reference Sec.1.10 Example 10 $AA5VV Syntax $AA5VVCHKcr AAVVCHKcr 11 $AA6Syntax $AA6CHKcr AAVCHKcr 12 $AA8Syntax $AA8CHKcr 13 $AA8V Syntax $AA8VCHKcr Syntax $AA9DataCHKcr Related Command Sec.2.8 $AA314 $AA9Data AA address of response module 00 to FF Example AASCHKcr 15 $AABSyntax $AABCHKcr AADataCHKcr 16 $AAFSyntax $AAFCHKcr 17 $AAM Syntax $AAMCHKcr 18 $AAZData Syntax $AAZDataCHKcr Syntax ~AAODataCHKcr Read address 01 module name, return 7018. Related Command19 ~AAOData Related Topic 20 ~AAEVSyntax ~AAEVCHKcr AASOOIICHKcr 21 @AADISyntax @AADICHKcr Level. Example High 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr 24 @AAHIData 25 @AALOData Syntax @AADACHKcr Related Command Sec.2.23 @AAEAT Related Topic26 @AADA 27 @AACA Syntax @AACACHKcr Syntax @AARHCHKcr Read address 01 high alarm, return +2.5000. Related Command28 @AARH 29 @AARL Syntax @AARECHKcr Read address 01 event counter, return 1234. Related Command30 @AARE 31 @AACE Syntax @AACECHKcr Syntax ~**CHKcr 32 ~Description Host OK Response No response. Example Syntax ~AA0CHKcr Host watchdog timeout flag, 0=Clear, 1=Set Example33 ~AA0 AASSCHKcr 34 ~AA1 Syntax ~AA1CHKcr 35 ~AA2 Syntax ~AA2CHKcr 36 ~AA3EVV Syntax ~AA3EVVCHKcr AAPPSSCHKcr 37 ~AA4Syntax ~AA4CHKcr SS Safe Value, data format is same as PP Example 38 ~AA5PPSS Syntax ~AA5PPSSCHKcr INIT* pin Operation Module Status Digital Output Dual Watchdog OperationDigital Input and Event Counter Dual Watchdog = Module Watchdog + Host Watchdog High/Low Alarm Thermocouple Measurement