American Megatrends MAN-STOR-ITX27-CLI manual Initial Setup, NIC-1

Page 8

Initial Setup

Network Configuration

Once the StorTrends® iTX is installed in a new system, please ensure that the initial network configuration is proper. The system factory defaults to DHCP setup. The configured network settings can be verified by the following CLI commands:

CLI> get	–-type or –t port
	-–name	or	–n NIC-1
	--info	or	-i
	network <Enter>

Example: get –t port –n nic-1 –i network

This will display the NIC-1 network settings.

To configure static IP to this port:

CLI> set	–-type or –t	port
	–-name or –n	NIC-1
	–-ip or –i 10.0.0.100
	–-mask or –m	255.255.255.0
	–-gate or –g	10.0.0.7 (optional)
	--pridns or –p 10.0.0.2 (optional)
	--secdns or –s 0.0.0.0 (optional)
	--dnssuff or	–f ami.com (optional)
	network <Enter>
	Example: set	–t port –n nic-1 –i 10.0.0.100 –g 10.0.0.7
	-p 10.0.0.2 –s 0.0.0.0 –f ami.com network

Here 10.0.0.100 is the static IP address, 255.255.255.0 is netmask and 10.0.0.7 is the network gateway.

2StorTrends® iTX Software CLI (Command Line Interface) (Version 2.7) User’s Guide

Image 8

Contents

MAN-STOR-ITX27-CLI 06/07/2010 Revision History Preface Table of Contents Technical Support Limited WarrantyLimitations of Liability Disclaimer Overview of CLI Accessing CLIPreface Initial Setup NIC-1Volume Configuration This will list the available RAID LD’s present in the systemPage Similarly a SAN volume can be created as follows To create a target, use the following commandsThen, to enable the target, use the syntax below Next step is to activate a port for iSCSI trafficCommand Set ChapterFor example To find out how the show command works, type CLIshow -h EnterAlert Configuration These commands configure the way alerts are generatedThese commands configure the time zone and date Date/Time ConfigurationDomain Configuration Event log Commands These commands display or clear the event logFirewall Configuration These commands configure the network firewall optionsThese commands get the health information General Server ConfigurationHealth Configuration ISCSI Configuration Command Argument Description License configuration These commands configure the LicenseNetwork Controller Configuration NAS Quota Configuration For exmaple set -t user -u test1 -p test1 -f Test1 ug NAS User / Group ConfigurationList retrieved will be given for both instead of singly Protocol Configuration RAID & Disk Management Commands Command Argument Description Upgrades the firmware for a Share, Directory & ACL Configuration These commands work on NAS shares and directoryLevel for NT System Control Configuration Volume and Snapshot CommandsThese commands configure the System controls 3provisiontype 0-ThinCommand Argument Description Command Argument Description Xml UPS ConfigurationThese commands configure the UPS for power management For example update -l c0v0 -p 50 -m Syncreplica Synchronous replicationFor example For example Update -l c0v0 -p 50 -m 172.16.70.102 Update -l c0v0 -g rg0 syncreplicaUtilization bandwidth utilization These commands configure asynchronous replicationAsynchronous Replication Command Argument Description Failedduetorollback Command Argument Description Command Argument Description Command Argument Description Journal Volume Management These commands configure a journal and journal fileExample Example Get -t journalfile -c Cont0 -f jf0 journalPage Recovery Wizard These commands are to view cdp for journal fileThese commands are used as part of recovery wizard Continuous Data ProtectionThese commands are used as part of SRM Storage Resource ManagementList the tasks in report, pending Workflow queueThese commands are used as part of snap validation Local and Replicated Snapshot validationPage Appendix a Error Codes Code 175 Error in mounting the share 338 License file read write error Code Code Code Code Description Code Description Code Description