American Megatrends MAN-STOR-ITX27-CLI manual Continuous Data Protection, Recovery Wizard

Page 47

Continuous Data Protection

These commands are to view cdp for journal file.

rollback	-c/--container <containername>	Performs rollback on journal file.
cdp	-f/--journalfile <jfname>
	Example:
	rollback -c c0 -f jf0 cdp
review	-c/--container <containername>	Performs CDP Review operation
cdp	-f/--journalfile <jfname>	for journal file.
	-s/--basesnap <t-number>
	-t/--deltatime <deltat from basesnap>	1) -t and -i options ignored if -e is
	-i/--deltaio <delta IO from deltat>	specified
	-e/--eventindex <deltaevt from basesnap>
		2) Delta time and IO must not be
	Example:	specified for event review
	review -c c0 -f jf0 -s 1 -t 10 -i 54 cdp
	review -c c2 -f jf1 -s 1 -e 15 cdp
delete	-c/--container <containername>	Delete a currently existing CDP
cdp	-f/--journalfile <jfname>	session.
	Example:
	delete -c c0 -f jf0 cdp
get	-t review	Gets CDP Review Progress
cdp	-c/--container <containername>	operation for journal file.
	-f/--journalfile <jfname>
	Example:
	get -t review -c c0 -f jf0 cdp

Recovery Wizard

These commands are used as part of recovery wizard.

get recoverywizard	-c/--container <container name>	Get recoverywizard lists the snaps
	-v/--volume<volumename>	that have common‘t’ number
	-x/--xml (optional)	across the given set of volume(s).
	-n/--tnum <writable snapshot number> (optional)
	Example:
	get -c c0 -v vol1 recoverywizard
	get -c c0 -v vol1 -v vol2 -v vol3 -n 1 -x
	recoverywizard

review	-c/--container <container name>	Review recoverywizard activates a
recoverywizard	-v/--volume<volumename>	set of snaps that have common ‘t’
	-s/--snap<snapname>	number across the given set of
	-x/--xml (optional)	volume(s), adds them to a LUN
		and enables them as a target to
	Example:	which an initiator can login to
	review -c c0 -v vol1 -s snapv1T1 recoverywizard	review the data.
	review -c c0 -v vol1 -v vol2 -v vol3 -s snap4v1T2
	–s snap5v2T2 -s snap6v3T2 recoverywizard
		Chapter Two: Command Set 41

Image 47

Contents

MAN-STOR-ITX27-CLI 06/07/2010 Revision History Preface Table of Contents Technical Support Limited WarrantyLimitations of Liability Disclaimer Overview of CLI Accessing CLIPreface NIC-1 Initial SetupThis will list the available RAID LD’s present in the system Volume ConfigurationPage To create a target, use the following commands Similarly a SAN volume can be created as followsNext step is to activate a port for iSCSI traffic Then, to enable the target, use the syntax belowChapter Command SetCLIshow -h Enter For example To find out how the show command works, typeThese commands configure the way alerts are generated Alert ConfigurationThese commands configure the time zone and date Date/Time ConfigurationDomain Configuration These commands display or clear the event log Event log CommandsThese commands configure the network firewall options Firewall ConfigurationThese commands get the health information General Server ConfigurationHealth Configuration ISCSI Configuration Command Argument Description These commands configure the License License configurationNetwork Controller Configuration NAS Quota Configuration For exmaple set -t user -u test1 -p test1 -f Test1 ug NAS User / Group ConfigurationList retrieved will be given for both instead of singly Protocol Configuration RAID & Disk Management Commands Command Argument Description Upgrades the firmware for a These commands work on NAS shares and directory Share, Directory & ACL ConfigurationLevel for NT 3provisiontype 0-Thin System Control ConfigurationVolume and Snapshot Commands These commands configure the System controlsCommand Argument Description Command Argument Description Xml UPS ConfigurationThese commands configure the UPS for power management Synchronous replication For example update -l c0v0 -p 50 -m SyncreplicaFor example Update -l c0v0 -g rg0 syncreplica For example Update -l c0v0 -p 50 -m 172.16.70.102Utilization bandwidth utilization These commands configure asynchronous replicationAsynchronous Replication Command Argument Description Failedduetorollback Command Argument Description Command Argument Description Command Argument Description Example Get -t journalfile -c Cont0 -f jf0 journal Journal Volume ManagementThese commands configure a journal and journal file ExamplePage Continuous Data Protection Recovery WizardThese commands are to view cdp for journal file These commands are used as part of recovery wizardWorkflow queue These commands are used as part of SRMStorage Resource Management List the tasks in report, pendingLocal and Replicated Snapshot validation These commands are used as part of snap validationPage Appendix a Error Codes Code 175 Error in mounting the share 338 License file read write error Code Code Code Code Description Code Description Code Description