American Megatrends MAN-772 manual For, P54C P55C

Page 19

Step 3 Configure CPU, Continued

ICS 9147 Clock Generator The following CLK1, CLK2, and CLK3 settings apply only if an

ICS 9147 clock generator is mounted on the motherboard.

External

CLK1

CLK2

FREQ1

 

(CPUCLK)

 

 

 

 

66 6 MHz

Short Pins 1-2

Short Pins 2-3

Short Pins 2-3

 

60 MHz

Short Pins 2-3

Short Pins 2-3

Short Pins 2-3

 

55 MHz

Short Pins 1-2

Short Pins 1-2

Short Pins 2-3

 

50 MHz

Short Pins 2-3

Short Pins 1-2

Short Pins 2-3

 

 

 

 

 

 

 

ICW or PhaseLink Clock Generator The following CLK1, CLK2, and CLK3 settings apply only if an ICW or PhaseLink clock generator is mounted on the motherboard.

External

CLK1

CLK2

FREQ1

 

(CPUCLK)

 

 

 

 

66 6 MHz

Short Pins 1-2

Short Pins 1-2

Short Pins 1-2

 

60 MHz

Short Pins 2-3

Short Pins 1-2

Short Pins 1-2

 

55 MHz

Short Pins 2-3

Short Pins 2-3

Short Pins 1-2

 

50 MHz

N/A

N/A

N/A

 

 

 

 

 

 

 

CPU/Bus Frequency Ratio FREQ1, FREQ2, and FREQ3 are 3-pin bergs that set the ratio of the internal CPU frequency to the bus clock.

For

For

For

FREQ1

FREQ2

FREQ3

P54C

P55C,

K5

 

 

 

 

and K6

 

 

 

 

3x

3x

2x

Short Pins 1-2

Short Pins 2-3

Short Pins 1-2

2.5x

2.5x

1.75x

Short Pins 2-3

Short Pins 2-3

Short Pins 1-2

2x

2x

N/A

Short Pins 2-3

Short Pins 1-2

Short Pins 1-2

1.5x

3.5x

1.5x

Short Pins 1-2

Short Pins 1-2

Short Pins 1-2

Cont’d

Chapter 1 Hardware Installation

15

Image 19
Contents Apollo IV Pentium PCI ISA MotherboardGuide Ii Apollo IV PCI Pentium ISA Motherboard User’s Guide Preface Phone Number CharacteristicsTechnical Support Static Electricity Packing ListCPU Manufacturer Supported CPU Speeds OverviewChipset Type of System Supported System Memory Socket Overview Parallel Port Fast ATAUltra DMA/33 FloppyCPU External Clock Frequency PCI Expansion Slot Frequency MouseInfrared DMIMotherboard Height Restrictions Apollo IV DimensionsStep Action Installation StepsApollo IV Motherboard Layout Step Action Unpack the MotherboardSet Jumpers PWR1 Setting DescriptionFlash ROM Type Avoid Static ElectricityExternal Configure CPUP54C P55C ForP54C Summary of Jumper Setting for Intel Pentium CPUsSummary of Jumper Setting for AMD K5 and K6 CPUs Value Description AMD-K6 Step Action Total System Install MemorySupported System Memory Configurations Type of System Memory Supported System Memory SocketMemory Display Should supply these parts Install the MotherboardInstall Motherboard Attach Cables ConnectorAttach Cables Pin Description Power Connector PinoutPin MotherboardPin Description Connector Signal Descriptions Pins 12 13 14Connect Onboard I/O Pin Description Signal DescriptionSLCTIN# Pin Signal DescriptionAttach Floppy Drive Twist in Floppy Cable Floppy Connector PinoutPin Use Attach IDE Drive Attach IDE Drive Primary Pinout The Primary IDE pinout is Secondary IDE Pinout The Secondary pinout is Test and Configure Page Winbios Setup Using the Keyboard with Winbios Setup Using a Mouse with Winbios SetupKeystroke Action Winbios Setup Menu Drive Type How to Configure Standard SetupParameter Description 65535 1223 152 MB Hard Disk Drive TypesSetting Description Advanced SetupAdvanced Setup Type of Armd Device Drive Emulation Configured Advanced Setup Disabled Chipset Setup Power Management Setup Power Management Setup Cont’d PCI/PnP SetupSnoop Bit Action DMA Channel Option Optimal Default Fail-Safe DefaultOffboard PCI IDE Primary IRQ Peripheral SetupPrimary Prefetch IDE Secondary IRQ optionsPeripheral Setup EPP Version Setting DescriptionSecurity Amibios Password SupportChanging a Password Setting a PasswordAnti-Virus Utility Optimal OriginalFail-Safe Programming the Flash Eprom Programming the Flash ROMStep Expected behavior Programming the Flash ROMNumber of Beeps Description Code Description Bootblock Code Checkpoint Codes