Matsushita CF-08TX1A1M manual Shutting Down power off the wireless display

Page 14

When returning the wireless display to its condition at the time of shipment

Perform the following procedure while the wireless display is turned off.

AConnect your wireless display to a power outlet.

BPress the power button with the keyboard button and USER button pressed until the message “Reset the device to factory default...” appears.

When the [Enter Password] screen appears, enter the Supervisor Pass- word and tap [OK].

CSelect [Yes].

NOTE

When you turn on the wireless display next time, the calibration screen will appear.

Shutting Down (power off the wireless display)

1 Press the power button for one or two seconds until the message “Preparing to Power off…” appears.

When shutting down forcefully, press the power button for four seconds or longer.

4-3

Image 14

Contents CF-08TX1A1M Page Page Avoid Extreme Heat, Cold and Direct Sun- light PrecautionsAvoid Heat Do Not Put into a Micro- waveStop Using Contents Specifications Main SpecificationsWireless LAN BluetoothDisclaimer Trademarks IntroductionCopyright Description of parts Battery pack Headphone jackStylus holder Security lock Speaker Expansion bus connector Microphone jackUsing the Tether Attaching the TetherConnect to the server Turn on the wireless displayStarting up/Shutting Down When settings have been changed Make the settings only for the SupervisorWhen terminating the connection When deleting settingsShutting Down power off the wireless display Flow Chart Diagnosis & RepairTroubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Display TroubleshootingStarting Up TouchscreenShut Down Wireless CommunicationConnecting Peripherals SoundBlock Diagram DC/DC VCC5P0V LCD FET Wiring Connection Diagram Dock CON PCBPreparation Disassembly/ReassemblyRemoving the Battery Pack Removing the Display UnitRemoving IO Power PCB Removing the Main PCBRemoving the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the Dock Con PCB Removing the Bluetooth Wlan R PCBRemoving the Wlan L PCB Removing the SW LED PCBRemoving the LCD Unit and the Inverter Reassembly Instructions Setting the LCD Unit and the InverterPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Setting the SW LED PCB Assembly of the LCD BlockAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Bluetooth Wlan R PCB Setting the Wlan L PCBSetting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the Wlan PCB Setting the IO Power PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly Exploded View 10-110-2 10-3 Replacement Parts List 11-111-2 11-3 11-4 REF. no and Area11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 Resistor Array11-16 11-17 11-18 11-19 11-20 ERJ3GEYJ562V11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB CF-08 Schematic Diagram IO Power 1 I/F Connector RJ45LANIO Power 2 DCIN/ Battery For Cradle DC-INIO Power 3 Charger LTC4008EGN#TRPBFIO Power 4 VA3,VA5 SENSE2IO Power 5 EC ECFlashIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board