Matsushita CF-08TX1A1M manual Assembly of the SW LED PCB

Page 36

Assembly of the SW LED PCB

 

LED Lens

 

 

Power

 

 

Button

Power Button

 

Sheet

 

 

Attach.

 

 

 

 

 

Scroll

 

 

 

Button

Scroll Button

 

Sheet

 

 

Asymmetric shape

 

User Button

SW Rubber

Ensure it is attached in the notch.

Press the scroll button. (3.0 to 4.0 Kgf)

SW

Board

in FPC direction

Screw-1->Screw-3 Screw-1

0~1mm

Tape

 

 

Order of fixing

 

 

Place the stiffening

 

 

 

plate downward.

 

 

 

Tape

After attaching FPC, put the

 

 

 

Board and fix it with a tape:

 

 

 

CN edge standard.

 

 

 

 

 

 

 

1~2mm

SW

Board

Stopper

Plate

Screw-2

Screw-3

Lamp CN

Safety Working

Lamp CN

Inverter CN Tape

Match the end.

Inverter Case

After passing the case through, attach to the back side of the Board.

Note)Avoid any stress on the transformer of the Inverter and the coil.

Important Parts for Safety

Inverter

0 to 1 mm from the line

Inverter

Fix Tape

Clamper

0 to 1 mm

 

from the line

Safety Working

 

Pass it through

 

the clamper.

 

SW Card Cable

Ensure the Cable does

not run over the LCD Frame.

Safety Working

Pass the Cable between the Board and rib.

Remove the Release Paper on the back side and attach it, matching it to the edge of the case.

Match.

Inverter Cable

Safety Working

Clamper

Pass it through the clamper.

Wrap around the Conductive Cloth on this side.

9-12

Image 36
Contents CF-08TX1A1M Page Page Precautions Avoid HeatAvoid Extreme Heat, Cold and Direct Sun- light Do Not Put into a Micro- waveStop Using Contents Specifications Main SpecificationsWireless LAN BluetoothIntroduction CopyrightDisclaimer Trademarks Battery pack Headphone jack Stylus holder Security lock Speaker Expansion bus connectorDescription of parts Microphone jackUsing the Tether Attaching the TetherTurn on the wireless display Starting up/Shutting DownConnect to the server Make the settings only for the Supervisor When terminating the connectionWhen settings have been changed When deleting settingsShutting Down power off the wireless display Flow Chart Diagnosis & RepairTroubleshooting Self Test Program CPU Type checkSdram march test Test register check for the source microcomputer ID check for 2700GChip ID check for LAN9118 How to Restart Troubleshooting Starting UpDisplay TouchscreenWireless Communication Connecting PeripheralsShut Down SoundBlock Diagram DC/DC VCC5P0V LCD FET Wiring Connection Diagram Dock CON PCBDisassembly/Reassembly Removing the Battery PackPreparation Removing the Display UnitRemoving IO Power PCB Removing the Main PCBRemoving the Wlan PCB Removing the Speaker Removing the Audio Con PCBRemoving the USB PCB Removing the Bluetooth Wlan R PCB Removing the Wlan L PCBRemoving the Dock Con PCB Removing the SW LED PCBRemoving the LCD Unit and the Inverter Reassembly Instructions Setting the LCD Unit and the InverterPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Setting the SW LED PCB Assembly of the LCD BlockAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Bluetooth Wlan R PCB Setting the Wlan L PCBSetting the USB PCB Setting the SpeakerSetting the Audio Con PCB Setting the Wlan PCB Setting the IO Power PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly Exploded View 10-110-2 10-3 Replacement Parts List 11-111-2 11-3 11-4 REF. no and Area11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 Resistor Array11-16 11-17 11-18 11-19 11-20 ERJ3GEYJ562V11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB CF-08 Schematic Diagram IO Power 1 I/F Connector RJ45LANIO Power 2 DCIN/ Battery For Cradle DC-INIO Power 3 Charger LTC4008EGN#TRPBFIO Power 4 VA3,VA5 SENSE2IO Power 5 EC ECFlashIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board