Matsushita CF-08TX1A1M manual Cable Hold Sheet

Page 47

*Note

Ensure the Cable does not run over the Cushions (a,b,c).

Safety Working

Note

Avoid any stress on the transformer and the coil.

Insert the cushions on the both sides with the "Caution to High Voltage" label facing front until they reach the bottom while matching the cushions to the A boss and the rib..(Top of the A boss and the cushions on the both sides must be on the same line.)

		Insert position
		shape of the A boss
	Connect.	Pass between
	Connect.	the Pins.
		the Pins.
		B

Safety Working

A				A	Cable Hold Sheet
		front side

Insert the cable.

Safety Working

Hook the FL Cable.

Hook the Spring Hook over the cable.

Note)

Do not strain the Cable on the both edges when removing the Inverter for repairment.

Attach cable hold sheet to the Pin after fixing the Cable. (B side and 1 must be on the same line oroverlaps.)

9-23

Image 47

Contents CF-08TX1A1M Page Page Do Not Put into a Micro- wave PrecautionsAvoid Heat Avoid Extreme Heat, Cold and Direct Sun- lightStop Using Contents Main Specifications SpecificationsBluetooth Wireless LANDisclaimer Trademarks IntroductionCopyright Microphone jack Battery pack Headphone jackStylus holder Security lock Speaker Expansion bus connector Description of partsAttaching the Tether Using the TetherConnect to the server Turn on the wireless displayStarting up/Shutting Down When deleting settings Make the settings only for the SupervisorWhen terminating the connection When settings have been changedShutting Down power off the wireless display Diagnosis & Repair Flow ChartTroubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Touchscreen TroubleshootingStarting Up DisplaySound Wireless CommunicationConnecting Peripherals Shut DownBlock Diagram DC/DC VCC5P0V LCD FET Dock CON PCB Wiring Connection DiagramRemoving the Display Unit Disassembly/ReassemblyRemoving the Battery Pack PreparationRemoving the Main PCB Removing IO Power PCBRemoving the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the SW LED PCB Removing the Bluetooth Wlan R PCBRemoving the Wlan L PCB Removing the Dock Con PCBRemoving the LCD Unit and the Inverter Setting the LCD Unit and the Inverter Reassembly InstructionsPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Assembly of the LCD Block Setting the SW LED PCBAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Wlan L PCB Setting the Bluetooth Wlan R PCBSetting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the IO Power PCB Setting the Wlan PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly 10-1 Exploded View10-2 10-3 11-1 Replacement Parts List11-2 11-3 REF. no and Area 11-411-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 Resistor Array 11-1511-16 11-17 11-18 11-19 ERJ3GEYJ562V 11-2011-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB RJ45LAN CF-08 Schematic Diagram IO Power 1 I/F ConnectorFor Cradle DC-IN IO Power 2 DCIN/ BatteryLTC4008EGN#TRPBF IO Power 3 ChargerSENSE2 IO Power 4 VA3,VA5ECFlash IO Power 5 ECIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board