Matsushita CF-08TX1A1M manual Ffc

Page 44

Match to the center.

Shield Tape

FFC(Audio Card)

Shield Tape

Remove half of the Release

Paper and wrap around one loop.

Attachment

Standard –0.5(Board edge)

Match to the center.
0~0.5mm
	Ensure the Cable does not lean to the CN
	side. (Avoid coming over the A line edge
	to keep the inserting room for CN. )
0~0.5mm
FFC			End of the CN
FFC			0 to 0.5 mm
(Wireless Card) Busterade		Edge	Attachment
Safety Working		Edge	Attachment
FFC(Audio Card) Check Insert/Lock.	A	Sheet	–0.5(BoardStandardedge)

Safety Working

Check Insert/Lock.

1 0.5mm

Edge Sheet

Connect.

FFC				Tape
(Wireless Card)
(Wireless Card)			Safety Working

		Check Insert/Lock.

		Connect.
BT FFC			a
BT FFC	b
	b		c
	Connect.	Safety Working	c
	Connect.
		Check Insert/Lock.

Ensure the correct order. ANT Cable→FFC→Spring

1~3mm

Connect.

Safety Working

Check Insert/Lock.

0~1mm

Shield Tape

Tape

Power Cable

1~3mm

Match to the center. (–2)

*Note

Apply the load to attach. 20 to 30N (2.0 to 3.0 Kgf) *Paste Sheets firmly. 20~30N(2.0~3.0Kgf)

Loosen slightly not to strain.

Shield Tape
10–5mm
4–2mm
0~1mm	Remove the
	Remove the
	Release Paper and
	attach to the wall.

a

Ant.Cable

Handle FFC carefully. Hold down the arrow point of FFC lightly.

b

c

9-20

Image 44

Contents CF-08TX1A1M Page Page Precautions Avoid HeatAvoid Extreme Heat, Cold and Direct Sun- light Do Not Put into a Micro- waveStop Using Contents Specifications Main SpecificationsWireless LAN BluetoothDisclaimer Trademarks IntroductionCopyright Battery pack Headphone jack Stylus holder Security lock Speaker Expansion bus connectorDescription of parts Microphone jackUsing the Tether Attaching the TetherConnect to the server Turn on the wireless displayStarting up/Shutting Down Make the settings only for the Supervisor When terminating the connectionWhen settings have been changed When deleting settingsShutting Down power off the wireless display Flow Chart Diagnosis & RepairTroubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Troubleshooting Starting UpDisplay TouchscreenWireless Communication Connecting PeripheralsShut Down SoundBlock Diagram DC/DC VCC5P0V LCD FET Wiring Connection Diagram Dock CON PCBDisassembly/Reassembly Removing the Battery PackPreparation Removing the Display UnitRemoving IO Power PCB Removing the Main PCBRemoving the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the Bluetooth Wlan R PCB Removing the Wlan L PCBRemoving the Dock Con PCB Removing the SW LED PCBRemoving the LCD Unit and the Inverter Reassembly Instructions Setting the LCD Unit and the InverterPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Setting the SW LED PCB Assembly of the LCD BlockAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Bluetooth Wlan R PCB Setting the Wlan L PCBSetting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the Wlan PCB Setting the IO Power PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly Exploded View 10-110-2 10-3 Replacement Parts List 11-111-2 11-3 11-4 REF. no and Area11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 Resistor Array11-16 11-17 11-18 11-19 11-20 ERJ3GEYJ562V11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB CF-08 Schematic Diagram IO Power 1 I/F Connector RJ45LANIO Power 2 DCIN/ Battery For Cradle DC-INIO Power 3 Charger LTC4008EGN#TRPBFIO Power 4 VA3,VA5 SENSE2IO Power 5 EC ECFlashIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board