Matsushita CF-08TX1A1M manual Assembly of the Dock CON PCB

Page 38

■Assembly of the DOCK CON PCB

Order of fixing

Screw-1->Screw-5

Screw-4

Screw-3

Screw-5

Screw-1

Caption Tape

Attach the Hook firmly.Ensure the Connector Terminals of the Sheet ( Docking PCB sheet) do not run over.

(Attach in the arrow direction Screw-2horizontally.)

Match to the end of the

Connector. (0 to 1 mm)

Base Joint Cover

Match to the center of Mg square hole. (– 1 mm)

Ensure the direction is right.

Check Insert/Lock.

stiffening plate side

Cradle

Relay Card

		FFC
	Docking PCB Sheet	(Docking Card)
	Docking PCB Sheet
	Attach.	Busterade
		Busterade
	0~1mm	Rear Case Assy
	FFC Hold Cushion
	Attach to the	10+1mm
	top side of CN.	10+1mm
	top side of CN.

Docking

PCB side

Asymmetric shape

Docking Cover Sheet

9-14

Image 38

Contents CF-08TX1A1M Page Page Avoid Extreme Heat, Cold and Direct Sun- light PrecautionsAvoid Heat Do Not Put into a Micro- waveStop Using Contents Specifications Main SpecificationsWireless LAN BluetoothDisclaimer Trademarks IntroductionCopyright Description of parts Battery pack Headphone jackStylus holder Security lock Speaker Expansion bus connector Microphone jackUsing the Tether Attaching the TetherConnect to the server Turn on the wireless displayStarting up/Shutting Down When settings have been changed Make the settings only for the SupervisorWhen terminating the connection When deleting settingsShutting Down power off the wireless display Flow Chart Diagnosis & RepairTroubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Display TroubleshootingStarting Up TouchscreenShut Down Wireless CommunicationConnecting Peripherals SoundBlock Diagram DC/DC VCC5P0V LCD FET Wiring Connection Diagram Dock CON PCBPreparation Disassembly/ReassemblyRemoving the Battery Pack Removing the Display UnitRemoving IO Power PCB Removing the Main PCBRemoving the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the Dock Con PCB Removing the Bluetooth Wlan R PCBRemoving the Wlan L PCB Removing the SW LED PCBRemoving the LCD Unit and the Inverter Reassembly Instructions Setting the LCD Unit and the InverterPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Setting the SW LED PCB Assembly of the LCD BlockAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Bluetooth Wlan R PCB Setting the Wlan L PCBSetting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the Wlan PCB Setting the IO Power PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly Exploded View 10-110-2 10-3 Replacement Parts List 11-111-2 11-3 11-4 REF. no and Area11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 Resistor Array11-16 11-17 11-18 11-19 11-20 ERJ3GEYJ562V11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB CF-08 Schematic Diagram IO Power 1 I/F Connector RJ45LANIO Power 2 DCIN/ Battery For Cradle DC-INIO Power 3 Charger LTC4008EGN#TRPBFIO Power 4 VA3,VA5 SENSE2IO Power 5 EC ECFlashIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board