Matsushita CF-08TX1A1M manual Stop Using

Page 5

Stop Using

Should the battery emit an abnormal odor,

become hot to the touch, become discolored, change shape, or become in any way dif- ferent from normal, remove it from the wire- less display and stop using it.

Do not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged.

Do not expose the battery pack to water, or allow it to become wet. If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining bat- tery level becomes 30% to 40% and store it in a cool, dry place.

This wireless display prevents over- charging of the battery by recharging only when the remaining power is less than approx. 95% of capacity. The battery pack is not charged when the wireless display is first pur- chased. Be sure to charge it before using it for the first time. When the AC adaptor is connected to the wire- less display, charging begins auto- matically.

Should the battery leak and the fluid get into your eyes, do not rub your eyes. Immediately flush your eyes with clear water and see a doctor for medical treatment as soon as possi- ble.

NOTE

The battery pack may become warm during recharging or normal use. This is completely normal. Recharging will not commence if internal temperature of the battery pack is outside of the allowable tem- perature range (0 °C to 45 °C {32°F to 122°F}). Once the allowable range requirement is satisfied, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the tempera- ture is 10 °C {50°F} or below.)

If the temperature is low, the operat- ing time is shortened. Only use the equipment within the allowable tem- perature range.

The battery pack is a consumable item. If the amount of time the equip- ment can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one.

When transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.

Always power off the equipment when it is not in use. Leaving the equipment on when the AC adaptor is not connected will exhaust the remaining battery capacity.

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents CF-08TX1A1M Page Page Avoid Heat PrecautionsAvoid Extreme Heat, Cold and Direct Sun- light Do Not Put into a Micro- waveStop Using Contents Main Specifications SpecificationsBluetooth Wireless LANDisclaimer Trademarks IntroductionCopyright Stylus holder Security lock Speaker Expansion bus connector Battery pack Headphone jackDescription of parts Microphone jackAttaching the Tether Using the TetherConnect to the server Turn on the wireless displayStarting up/Shutting Down When terminating the connection Make the settings only for the SupervisorWhen settings have been changed When deleting settingsShutting Down power off the wireless display Diagnosis & Repair Flow ChartTroubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Starting Up TroubleshootingDisplay TouchscreenConnecting Peripherals Wireless CommunicationShut Down SoundBlock Diagram DC/DC VCC5P0V LCD FET Dock CON PCB Wiring Connection DiagramRemoving the Battery Pack Disassembly/ReassemblyPreparation Removing the Display UnitRemoving the Main PCB Removing IO Power PCBRemoving the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the Wlan L PCB Removing the Bluetooth Wlan R PCBRemoving the Dock Con PCB Removing the SW LED PCBRemoving the LCD Unit and the Inverter Setting the LCD Unit and the Inverter Reassembly InstructionsPreparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Assembly of the LCD Block Setting the SW LED PCBAssembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Wlan L PCB Setting the Bluetooth Wlan R PCBSetting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the IO Power PCB Setting the Wlan PCBSetting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly 10-1 Exploded View10-2 10-3 11-1 Replacement Parts List11-2 11-3 REF. no and Area 11-411-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 Resistor Array 11-1511-16 11-17 11-18 11-19 ERJ3GEYJ562V 11-2011-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB RJ45LAN CF-08 Schematic Diagram IO Power 1 I/F ConnectorFor Cradle DC-IN IO Power 2 DCIN/ BatteryLTC4008EGN#TRPBF IO Power 3 ChargerSENSE2 IO Power 4 VA3,VA5ECFlash IO Power 5 ECIO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board
Top Page Image Contents