Parker Products OEM650, OEM350X manual Sequence Inputs #1 #3 Signals 11, Shutdown Output Signal

Page 35
• Meets EIA RS-232C & CCITT V.28 specifications
•Signal ground

INSTALLATION • OEM650/OEM650X

typical configuration of this output.

Sequence Inputs #1 - #3 (Signals 11 - 13)

The OEM650X has three dedi- cated sequence inputs that allow you to control seven different sequences. Refer to the X commands for information on how to control these inputs. Sequence #Ø is not a valid sequence.

+5V

•Maximum low-level input: 0.8V (Sinks 1.2 mA)

4.75k

• Minimum high-level input: 2V

HCT244

Sequences are executed remotely by using one of the following logic patterns. (1 represents a +5V signal, Ø represents a ØV signal.)

Sequence #

Ø

1

2

3

4

5

6

7

SEQ Input #1

Ø

1

Ø

1

Ø

1

Ø

1

SEQ Input #2

Ø

Ø

1

1

Ø

Ø

1

1

SEQ Input #3

Ø

Ø

Ø

Ø

1

1

1

1

The figure represents a typical configuration of these outputs.

RS-232C—Tx (Signal 14), Rx (Signal 15), and Ground (Signal 7)

The OEM650X uses RS-232C as its communication medium. This indexer does not support hand- shaking. A typical three-wire (Rx, Tx, and Signal Ground) configu- ration is used). The figure represents a typical RS-232C configuration.

Tx

Rx

Shutdown Output (Signal 16)

The OEM produces a Shutdown

 

 

 

 

 

 

output that is identical to the

 

 

 

+5V

 

indexer's internal signal. This

 

 

 

 

 

• Minimum high-level output: 4.26V

output may be used to slave to

 

 

10k

(Source -24mA)

 

 

 

another drive or to monitor the

 

 

 

 

 

• Maximum low-level output: 0.44V

OEM650X. The Shutdown

 

 

 

 

 

(Sinks @ 23 mA)

 

 

 

 

 

 

output's default state is logic

 

 

ACTØ4

 

high. The figure represents a

 

 

 

 

 

 

 

 

 

 

 

 

typical configuration of this output. (Refer to the ST command.)

Closed Loop Operation

Closed loop moves require an external encoder to provide position correction signals. Motor position may be adjusted to reach the desired position. To implement the closed loop functions, you must

28

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Compumotor 88-013157-02A Important User InformationIntroduction ContentsInstallation Index Tuning & SpecificationsTroubleshooting Assumptions How To Use This User GuideUser Guide Contents Installation Process OverviewSoftware Reference Manual Installation PreparationOverview OEM650/OEM650X OEM350/350X Description Chapter ObjectiveOEM650 Description OEM650X DescriptionFeatures OEM650/OEM650X Ship kit Chapter ObjectivesEvaluation kits Quick Test OEM650/OEM650XOEM650/OEM650X Jumpers Top View Size 23 OEM650 Motors Parallel WiringSize 34 OEM Series Motors Parallel Wiring Motor Size Current Resistor Reversing VDC+ and VDC- can seriously damage the drive Quick Test OEM650 with Separate Indexer Quick Test OEM650X CompumotorIndexerLD3 OEM650/OEM650X Mounting OEM650/OEM650X DimensionsMounting Without a Heatsink Panel LayoutDrive Current Over-Temperature ProtectionMounting With OEM-HS1 13. OEM-HS1 DimensionsPanel layout for minimum depth is shown in Figure Mounting With OEM-HS2 16. OEM-HS2 DimensionsJumper #1 Motor Current Range Jumpers #2 #5 Motor ResolutionJumper Functions Jumpers #9 #10 Auto Standby Jumpers #6 #8 Motor Waveform ShapeJU9 Jumper #11 Auto TestAngular Misalignment Motor MountingAttaching the Load Parallel MisalignmentRigid Coupling CouplingsSingle-Flex Coupling Double-Flex CouplingStep Pulse Input Step Input Signal SpecificationDirection Input Signal Specification OEM650 Inputs and OutputsRemote Input Fault OutputGear Shift Input Step Signal 1 & Direction Signal 2 OutputsOEM650X Inputs and Outputs Output #1 Signal 10 and Output #2 Signal CW Signal 3 & CCW Signal 4 Limit InputsHome Position Input Signal Reserved SignalClosed Loop Operation Sequence Inputs #1 #3 Signals 11RS-232C-Tx Signal 14, Rx Signal 15, and Ground Signal Shutdown Output SignalEncoder Inputs A, B, Z Signals Trigger Inputs #1 #3 Signals 20Address Signals #1 #3 Signals 23 Daisy Chaining 20. Daisy Chain ConfigurationMotor Type Sizing Power SupplyConnection CalculationsCurrent Amps Power DumpMid-Range Instability Tuning ProceduresShort-Circuit Protection ResonanceStethoscope Method Gauging Motor ResonanceTachometer Method Sounding Board MethodTouch Method Tuning the Drive to the MotorMotor Waveforms Performance Specifications OEM650/OEM650X with OEM57-83-MOS OEM57 Motors Parallel Configuration OEM83 Motors Tuning & Specifications OEM650/OEM650X Reducing Electrical Noise Drive MaintenanceMotor Maintenance Problem IsolationFront Panel LEDs Common Problems and SolutionsSymptoms Possible Causes Solutions Symptoms Probable Causes Solutions RS-232C Problems Testing the MotorReturning the System Software Debugging TipsOEM650/OEM650X Troubleshooting Troubleshooting OEM650/OEM650X Index Index OEM650/OEM650X OEM650X Inputs & Outputs Screw Terminal Connections OEM650 Inputs & Outputs, and Internal Connections

OEM650X, OEM650, OEM350, OEM350X specifications

Parker Products provides an exceptional lineup of industrial-grade portable adhesive applicators, including the OEM350X, OEM350, OEM650, and OEM650X. These models are designed to meet the demands of various manufacturing processes, delivering reliable and precise adhesive application for diverse industries such as automotive, woodworking, and packaging.

The OEM350 series, including both OEM350 and OEM350X, is characterized by its lightweight yet durable construction, allowing for ease of handling and transport. This series is particularly known for its versatility in handling various adhesive types, including polyurethane, hot melt, and cyanoacrylate adhesives. The OEM350 features a robust performance with a maximum output of 350 lbs per hour, ensuring efficient production rates while maintaining high-quality bonding. The OEM350X variant enhances these features with advanced temperature control technology, enabling users to maintain optimal adhesive viscosity for different applications.

On the other hand, the OEM650 and OEM650X models are designed for heavier-duty applications. The OEM650 can deliver up to 650 lbs of adhesive per hour, making it suitable for high-volume manufacturing processes. Its larger tank capacity and efficient heating mechanism allow for extended operational periods between refills, which significantly boosts productivity. The OEM650X takes performance a notch higher with integrated smart technology, which provides real-time monitoring of adhesive quality and system health, helping to reduce downtime and maintain efficiency in production.

All models in this range are equipped with user-friendly interfaces for easy operation. The control panels allow operators to set precise temperature and pressure settings, which can be adjusted to fit particular production needs. Additionally, the equipment is built with safety features such as automatic shut-offs and alarm systems, ensuring safe operation in busy manufacturing environments.

Parker Products’ OEM series stands out not only for its performance but also for its commitment to innovation. With advancements like modular design for easy maintenance and scalability, these applicators are designed to grow with your business. The robust performance, versatile application, and advanced technologies of the OEM350X, OEM350, OEM650, and OEM650X make them invaluable tools in the modern manufacturing landscape, driving efficiency and quality in adhesive applications.
Top Page Image Contents