NordicTrack 3G10WV manual Setup, Option Description

Page 26

5.1Setup

This screen allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. The Wireless Guest Network function adds extra networking security when connecting to remote hosts.

Option	Description

Enable Wireless	A checkbox that enables (default) or disables the wireless LAN interface. When selected,
	the Web UI displays Hide Access point, SSID, BSSID and Country settings.

Hide Access Point	Select Hide Access Point to protect the access point from detection by wireless active
	scans. To check AP status in Windows XP, open Network Connections from the start Menu
	and select View Available Network Connections. If the access point is hidden, it will not be
	listed there. To connect a client to a hidden access point, the station must add the access
	point manually to its wireless configuration.

SSID	Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be
[1-32 characters]	configured with the correct SSID to access the WLAN. If the SSID does not match, that user
	will not be granted access.

BSSID	The BSSID is a 48bit identity used to identify a particular BSS (Basic Service Set) within
	an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control)
	address of the AP (Access Point) and in Independent BSS or ad hoc networks, the BSSID is
	generated randomly.

Country	A drop-down menu that permits worldwide and specific national settings. Each country
	listed below enforces specific regulations limiting channel range:
	•	USA = worldwide
	•	Australia = 1-11
	•	Japan = 14
	•	Jordan = 10-13
	•	Israel = 1-13

Wireless Guest	The Guest SSID (Virtual Access Point) can be enabled by selecting the Enable Wireless Guest
Network	Network checkbox. Rename the Wireless Guest Network as you wish.
	NOTE: Remote wireless hosts cannot scan Guest SSIDs.

26 – 3G10WV HSPA Wi-Fi Router with Voice

Image 26

Contents 3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Important Notice and Safety Precaution PrefaceTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Features Package ContentsAssociated port LED IndicatorsColor Mode Description Rear Panel Quick Setup Configure the router through the Web User Interface WUI Quick SetupSetup Procedure Save the router configuration and reboot see sectionWeb User Interface Default Settings Web User InterfaceClick OK to submit the settings TCP/IP SettingsDhcp Mode Login Procedure To login to the web interface, follow the steps belowWeb User Interface Homepage Basic / HomeFollowing table provides further details Fields Description3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 20 3G10WV Hspa Wi-Fi Router with Voice PIN Lock Off PIN ConfigurationPIN Code Protection PIN Lock On PIN Code Change Wireless Wireless Setup Option DescriptionClick Save/Apply to configure the wireless security options SecurityWEP Encryption will also be enabled Card. If the Ssid does not match, access is deniedAuthentication Select SsidConfiguration AP Isolation Broadcast and multicast messages. The default isDefault is disabled Point can be linkedMbit/s Dsss specification as described in Ieee Std 54g ModeOnly mode 54g ProtectionMAC Address Deny Rejects access for the specified MAC addressesMAC Filter Can be addedFeature Options Wireless BridgeClick Save/Apply to implement new configuration settings Is generated randomly Authorized Lists those devices with authorized accessStation Info AssociatedManagement Device Settings ManagementUpdate Settings Restore Default38 3G10WV Hspa Wi-Fi Router with Voice By default, Snmp agent is enabled on the gateway Configure Snmp agent on 3G10WVSetting up Snmp agent Press Save/Apply to activate settingSimple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup Advanced Setup This chapter explains advanced setup for your RouterHosts connected to Hspa 7.2 Mbps Wi-Fi Router Setting. By default NAT is enabledThese options are used for special Dhcp set up Local Area Network LANShow up on the same page as below Enable DhcpEnable Dhcp Server Server RelayNetwork Address Translation NAT Port ForwardingOptions Description Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured External Port EndPort Triggering Trigger Protocol TCP, TCP/UDP or UDP Open Port Start Demilitarized DMZ HostTrigger Port End Open Port End52 3G10WV Hspa Wi-Fi Router with Voice Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing 56 3G10WV Hspa Wi-Fi Router with Voice DNS Server Configuration Domain Name Servers DNSDynamic DNS Options DescriptionsVoice Configuring your 3G10WV for placing Voice Calls VoiceStatus Status Diagnostics Test DescriptionSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Quality Ec/Io Status BCS Battery Charge LevelStatus Strongest cells Network RegistrationStatistics Interface Shows connection interfacesService Shows the service type Field Description RouteSelect Route to display the paths the Router has found But may be needed by routing daemonsClick ARP to display the ARP information Dynamic Host Configuration Protocol DhcpARP Click Dhcp to display the Dhcp informationPing CLI commands Via Telnet End the telnet session CLI commands via TelnetHelp Synopsis help ? ExampleDescription Display the 3G network connection status ExamplesSierra show --mode Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Description Display the Imsi and Imei value Sierra show --hsdcat !HSDCATSynopsis sierra set --apn profile apn profile 1 Custom APN Sierra show --mode mode UmtsExample Set the Custom APN to test.test Sierra show -auth 1 Profile1 PAP Synopsis sierra set --comp profile type enabledisableExample Enable the IP header compression for Custom APN PIN code configuration Connect / Disconnect PPP sessionChanged the PIN code successfully PUK code unlock Synopsis sierra show --PIN-LOCK ExampleSierra set --PIN-CHG 0000 Sierra set --PUK 11111111 0000 PUK unlock successfullyOptions Enable WlanValid value 32 characters string --country countryStr Description Set the wireless LAN channel Valid value 0~14Means auto select channel. Default value Default value 0 --mrate rateVal Default value 2346 --dtim dtimIntervalDefault value long ExampleOptions Example Remove MACaddress Options Configure wireless LAN MAC filterSynopsis Description add one MAC Address entry --remove MACaddressDescription set remote bridge MAC address Advance Wlan security wpaGTKRekey =Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information