NordicTrack 3G10WV Wireless Bridge, Click Save/Apply to implement new configuration settings

Page 33

5.5Wireless Bridge

The following screen appears when selecting Wireless Bridge, and goes into a detailed explanation of how to configure wireless bridge features of the wireless LAN interface.

Click Save/Apply to implement new configuration settings.

Feature	Options

AP Mode	Selecting Wireless Bridge (Wireless Distribution System) disables Access Point (AP)
	functionality while selecting Access Point enables AP functionality. In Access Point mode,
	wireless bridge functionality will still be available and wireless stations will be able to
	associate to the AP.

Bridge Restrict	Selecting Disabled in Bridge Restrict disables Wireless Bridge restriction, which means
	that any wireless bridge will be granted access. Selecting Enabled or Enabled (Scan)
	allows wireless bridge restriction. Only those bridges selected in Remote Bridges will be
	granted access. Click Refresh to update the station list when Bridge Restrict is enabled.

3G10WV HSPA Wi-Fi Router with Voice – 33

Image 33

Contents 3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesLED Indicators Color Mode DescriptionAssociated port Rear Panel Quick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see sectionWeb User Interface Web User Interface Default SettingsTCP/IP Settings Dhcp ModeClick OK to submit the settings To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings 3G Settings 3G Service SetupThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Configuration PIN Code ProtectionPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsAuthentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select SsidConfiguration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linkedOnly mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g ProtectionMAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be addedWireless Bridge Click Save/Apply to implement new configuration settingsFeature Options Station Info Authorized Lists those devices with authorized accessIs generated randomly AssociatedManagement Management Device SettingsRestore Default Update Settings38 3G10WV Hspa Wi-Fi Router with Voice Setting up Snmp agent Configure Snmp agent on 3G10WVBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate settingSimple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupThese options are used for special Dhcp set up Setting. By default NAT is enabledHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LANEnable Dhcp Server Enable DhcpShow up on the same page as below Server RelayPort Forwarding Network Address Translation NATSelected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port EndPort Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End52 3G10WV Hspa Wi-Fi Router with Voice Options Description Parental Control User Name User-defined label for this restrictionMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSVoice Voice Configuring your 3G10WV for placing Voice CallsStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network RegistrationInterface Shows connection interfaces StatisticsService Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemonsARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp informationPing CLI commands Via Telnet Help CLI commands via TelnetEnd the telnet session Synopsis help ? ExampleExamples Description Display the 3G network connection statusDescription Display the Imsi and Imei value Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Sierra show --mode Sierra show --hsdcat !HSDCATSierra show --mode mode Umts Example Set the Custom APN to test.testSynopsis sierra set --apn profile apn profile 1 Custom APN Synopsis sierra set --comp profile type enabledisable Example Enable the IP header compression for Custom APNSierra show -auth 1 Profile1 PAP Connect / Disconnect PPP session PIN code configurationSierra set --PIN-CHG 0000 Synopsis sierra show --PIN-LOCK ExampleChanged the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfullyWlan Options EnableDescription Set the wireless LAN channel Valid value 0~14 Means auto select channel. Default valueValid value 32 characters string --country countryStr Default value 2346 --dtim dtimInterval Default value 0 --mrate rateValExample Default value longOptions Example Synopsis Configure wireless LAN MAC filterRemove MACaddress Options Description add one MAC Address entry --remove MACaddressDescription set remote bridge MAC address Wlan security wpaGTKRekey = AdvanceWlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information