NordicTrack 3G10WV manual Wlan security WepCurrentKeyindex = 1 --macfilter

Page 91

wlan security WepKeyBit = 128 wlan security WepKey2 = wlan security WepKey3 =

wlan security WepCurrentKeyindex = 1 --macfilter

Description: display the list of parameters from macfilter option Example:

>wlan info --macfilter Wlan macfilter Info :

wlan macfilter mode = disabled wlan macfilter entry :

--wds

Description: display the list of parameters from wds opiton Example:

>wlan info --wds

Wlan wds Info : wlan wds mode = ap

wlan wds restrict mode = disabled --station

Description: display the list of authenticated wireless stations and their status Example:

> --wlan info --station

--wlan info --station: not found

Configure Access Control

Description: to list and to configure access control from LAN & WAN.

(1) To set up the access control list.

Synopsis: remoteaccess service [--service <servicename>] <--interface <nonelocalremoteboth> >

<servicename>: FTP, HTTP, ICMP, TELNET, SSH, TFTP

<nonelocalremoteboth>:

3G10WV HSPA Wi-Fi Router with Voice – 91

Image 91

Contents 3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesColor Mode Description LED IndicatorsAssociated port Rear Panel Quick Setup Save the router configuration and reboot see section Quick SetupSetup Procedure Configure the router through the Web User Interface WUIWeb User Interface Web User Interface Default SettingsDhcp Mode TCP/IP SettingsClick OK to submit the settings To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings 3G Service Setup 3G SettingsThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Code Protection PIN ConfigurationPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsSelect Ssid Card. If the Ssid does not match, access is deniedAuthentication WEP Encryption will also be enabledConfiguration Point can be linked Broadcast and multicast messages. The default isDefault is disabled AP Isolation54g Protection 54g ModeOnly mode Mbit/s Dsss specification as described in Ieee StdCan be added Deny Rejects access for the specified MAC addressesMAC Filter MAC AddressClick Save/Apply to implement new configuration settings Wireless BridgeFeature Options Associated Authorized Lists those devices with authorized accessStation Info Is generated randomlyManagement Management Device SettingsRestore Default Update Settings38 3G10WV Hspa Wi-Fi Router with Voice Press Save/Apply to activate setting Configure Snmp agent on 3G10WVSetting up Snmp agent By default, Snmp agent is enabled on the gatewaySimple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupLocal Area Network LAN Setting. By default NAT is enabledThese options are used for special Dhcp set up Hosts connected to Hspa 7.2 Mbps Wi-Fi RouterServer Relay Enable DhcpEnable Dhcp Server Show up on the same page as belowPort Forwarding Network Address Translation NATExternal Port End Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured Options DescriptionPort Triggering Open Port End Demilitarized DMZ HostTrigger Port End Trigger Protocol TCP, TCP/UDP or UDP Open Port Start52 3G10WV Hspa Wi-Fi Router with Voice Options Description User Name User-defined label for this restriction Parental ControlMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSVoice Voice Configuring your 3G10WV for placing Voice CallsStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Strongest cells Network Registration Status BCS Battery Charge LevelStatus Quality Ec/IoInterface Shows connection interfaces StatisticsService Shows the service type But may be needed by routing daemons RouteSelect Route to display the paths the Router has found Field DescriptionClick Dhcp to display the Dhcp information Dynamic Host Configuration Protocol DhcpARP Click ARP to display the ARP informationPing CLI commands Via Telnet Synopsis help ? Example CLI commands via TelnetHelp End the telnet sessionExamples Description Display the 3G network connection statusSierra show --hsdcat !HSDCAT Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Description Display the Imsi and Imei value Sierra show --modeExample Set the Custom APN to test.test Sierra show --mode mode UmtsSynopsis sierra set --apn profile apn profile 1 Custom APN Example Enable the IP header compression for Custom APN Synopsis sierra set --comp profile type enabledisableSierra show -auth 1 Profile1 PAP Connect / Disconnect PPP session PIN code configurationSierra set --PUK 11111111 0000 PUK unlock successfully Synopsis sierra show --PIN-LOCK ExampleSierra set --PIN-CHG 0000 Changed the PIN code successfully PUK code unlockWlan Options EnableMeans auto select channel. Default value Description Set the wireless LAN channel Valid value 0~14Valid value 32 characters string --country countryStr Default value 2346 --dtim dtimInterval Default value 0 --mrate rateValExample Default value longOptions Example Description add one MAC Address entry --remove MACaddress Configure wireless LAN MAC filterSynopsis Remove MACaddress OptionsDescription set remote bridge MAC address Wlan security wpaGTKRekey = AdvanceWlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information