NordicTrack 3G10WV manual Access Control

Page 41

6.4Access Control

The Access Control option found in the Management drop down menu, configures access related parameters in the following three areas:

•Services

•IP Addresses

•Passwords

Access Control is used to control local and remote management settings for your Router.

6.4.1Services

The Service Control List (SCL) allows you to enable or disable your Local Area Network (LAN) or Wireless Area Network (WAN) services by ticking the checkbox as illustrated below. These access services are available: FTP, HTTP, ICMP, SSH, TELNET, and TFTP. Click Save/Apply to continue.

3G10WV HSPA Wi-Fi Router with Voice – 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents 3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesAssociated port LED IndicatorsColor Mode Description Rear Panel Quick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see sectionWeb User Interface Web User Interface Default SettingsClick OK to submit the settings TCP/IP SettingsDhcp Mode To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 20 3G10WV Hspa Wi-Fi Router with Voice PIN Lock Off PIN ConfigurationPIN Code Protection PIN Lock On PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsAuthentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select SsidConfiguration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linkedOnly mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g ProtectionMAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be addedFeature Options Wireless BridgeClick Save/Apply to implement new configuration settings Station Info Authorized Lists those devices with authorized accessIs generated randomly AssociatedManagement Management Device SettingsRestore Default Update Settings38 3G10WV Hspa Wi-Fi Router with Voice Setting up Snmp agent Configure Snmp agent on 3G10WVBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate settingSimple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupThese options are used for special Dhcp set up Setting. By default NAT is enabledHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LANEnable Dhcp Server Enable DhcpShow up on the same page as below Server RelayPort Forwarding Network Address Translation NATSelected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port EndPort Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End52 3G10WV Hspa Wi-Fi Router with Voice Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSVoice Voice Configuring your 3G10WV for placing Voice CallsStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network RegistrationInterface Shows connection interfaces StatisticsService Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemonsARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp informationPing CLI commands Via Telnet Help CLI commands via TelnetEnd the telnet session Synopsis help ? ExampleExamples Description Display the 3G network connection statusDescription Display the Imsi and Imei value Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Sierra show --mode Sierra show --hsdcat !HSDCATSynopsis sierra set --apn profile apn profile 1 Custom APN Sierra show --mode mode UmtsExample Set the Custom APN to test.test Sierra show -auth 1 Profile1 PAP Synopsis sierra set --comp profile type enabledisableExample Enable the IP header compression for Custom APN Connect / Disconnect PPP session PIN code configurationSierra set --PIN-CHG 0000 Synopsis sierra show --PIN-LOCK ExampleChanged the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfullyWlan Options EnableValid value 32 characters string --country countryStr Description Set the wireless LAN channel Valid value 0~14Means auto select channel. Default value Default value 2346 --dtim dtimInterval Default value 0 --mrate rateValExample Default value longOptions Example Synopsis Configure wireless LAN MAC filterRemove MACaddress Options Description add one MAC Address entry --remove MACaddressDescription set remote bridge MAC address Wlan security wpaGTKRekey = AdvanceWlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information
Top Page Image Contents