Opticon NFT 2100 manual Opticon, IEC 825-1 Class 1 LED Devices

Page 17

Manual No. 25-ULNFT2100-01; Mar, 2005	NFT 2100 CCD Fixed Mount Barcode
Scanner
Section 6
Scanner Labeling

IEC 825-1 Class 1 LED Devices

The NFT 2100 has been examined and found to be a CE Class 1 LED Device according to the relevant requirements of IEC 825-1 and corresponding EN 60825-1 (1993-11) including amendment 1 (1997-09) and amendment 2 (2001-01).

The NFT 2100 scanner uses low-power visible LEDs. As with any very bright light source, such as a flashlight, you should avoid staring into the light. Momentary exposure to an IEC 825-1 Class 1 LED is not known to be harmful.

A manufacturer’s label, as shown below, indicating the manufacturer, product model, ordering number, serial number, CE mark and place of manufacture is affixed to each scanner.

OPTICON

NFT-2100-I-RS232C

Ordering Number

xxxxxx

Serial Number

******

MADE IN JAPAN

Section 7

Scanner Servicing and Maintenance

The NFT 2100 scanner contains no user adjustable or serviceable parts in the interior of the scanner. All product service must be performed by the Opticon Service Department in Orangeburg, NY. Opening the scanner will void the warranty.

The NFT 2100 is warranted for 7 year including parts and workmanship. If you need warranty or out-of- warranty repair, first call 1-800-636-0090to obtain a Returned Material Authorization (RMA) number. You will be provided a number and shipping instructions.

There is no scheduled maintenance required for the NFT 2100. The scanner can be cleaned using a water dampened, lint free or lens cloth. Be careful to avoid excessive moisture that would penetrate the housing or obscure the window. While use of cleaning fluids other than water are not recommended, a neutral detergent or ethanol would be preferred if necessary. Do not use bleach at full or diluted strength as damage to the painted case and/or window may result.

Page 14

Image 17

Contents User’s Guide NFTContents Organization of this Manual Product Overview Quick Start-Up ProcedurePage Optical Specifications Physical SpecificationsSymbologies Supported Specified operation β at + 6º or less. Recommended at 0º SkewPitch Tilt Rotation 35.4RS232 Communications Specifications Electrical Specifications Operating Voltage +5VDC + 5%Environmental Specifications Connector Pin-outsOrdering Information RegulatoryReading width or Field of View of the scanner Achieving Optimum PerformanceDistance to the Bar Code and Depth of field Readable Width or Field of View for the NFT Field-of-View Specification Based Upon 69º Degree SweepAvoiding Specular Reflection Quality Bar Code LabelsTips for Insuring Highest Data Integrity Measuring Scanner PerformanceApplication Notes Tips for Achieving High Throughput Tips for Verifying the Presence of a Bar Code Parameter Factory Default Setting Programming Menus & CommandsDefault Settings Modified and/or Customized Scanners Technical Assistance and SupportCommon Causes of Poor Performance IEC 825-1 Class 1 LED Devices OpticonPage Appendix a ESC Computer Command CRWhat if you make a mistake? Reset All Defaults U2 CommandAppendix B Options for Code Direct Input Miscellaneous Characters Prefix SuffixDirect Input Alpha/Numeric Characters Direct Input Ascii Control CharactersSetting the Trigger Functions Communication DelaysSelecting the Read Mode Scanner Timeout Trigger ModeGood Read LED Operation Xmit Error Trigger Enabled Mode onlyRedundant Decoding Delete/Deactivate Bar Code Symbologies Global Default & Scanner ConfigurationsScanner Timeout Trigger Enabled Mode only Appendix CDescription Command Symbologies Symbology SelectionComputer Function Bar Code Only MSI/PlesseyOnly EAN 13/8 +2 Symbology SelectionAdd/Activate Specific Bar Code Symbologies Add/Activate Specific Bar Code Symbologies Delete/Deactivate Bar Code SymbologiesComputer Function Command Description Disable all symbologiesDigits Add leading zero Options for UPCOptions for EAN-8 & EAN-13 7J JC JB IO IPOptions for Code 39 and IT Pharmaceutical Possible Disable IT PharmaceuticalOptions for Codabar NW-7 Enable normal, ABC & CX Codabar Disable ABC & Cx Codabar Page GG Enable transmit SCode as Interleaved 2 Command DescriptionF2 HF HG HJ HH HI Options for Interleaved & Industrial 2String format Meaning of Acronym Number of digits 15 total Options for IataOptions for Code-93 Options for Code-128 / EAN-128I2 IL IM Disable length setting on allScan Enable length setting H1 for all symbologies Creating a Prefix and/or Suffix Page UPC-E +2 or +5 Setting Prefixes Identifying the SymbologyMSI/Plessey O1 NC M9 NSetting Suffixes Identifying the Symbology O6 PC M Setting Suffixes Identifying the SymbologyDirect Input of Numeric Characters Direct Input of Alpha Characters Direct Input of Alpha Characters Lower Case Direct Input of Control Characters ETBDEL Computer Function Bar Code Command DescriptionDirect Input Characters Misc Direct Input Characters Misc Communication Parameters Terminal Communication HandshakingQ5 LB LC LD LE Communication DelaysSet buzzer at 3kHz Disable buzzerBuzzer Operation Selecting the Read Mode Setting the Trigger FunctionsUse as Com Port Command Multiple Read Mode. will readRead Scanner’s time out Scanner may not read the same bar Trigger Function Enabled S8 Trigger Function Disabled S7Mode YB YC YD YE Add-on Wait Mode Applies to UPC/EAN onlyZM Z1 Scanner Timeout Trigger Enabled Mode onlyBI BJ BK BL BM BN BO BH Multiple Read Reset TimeQuiet Zone Options ZO ZP ZQ ZR ZS ZT ZU ZVRedundant Decoding Transmitting Error IndicationsXE XD Programming No read Error Messages No read error messagesUI UJ Good Read LED OperationAppendix D Appendix E NFT 2100 Depth of Field ChartAppendix F Appendix G