Raymarine Radar Scanner manual Mounting surface sailboats, Mounting surface power boats

Page 17

Chapter 1: Overview

9

For open array scanners you should also consider the following points:

•Mounting Platform: The platform must be mechanically secure and capable of supporting the mass and inertia of the open array scanner. The complete unit weighs: 48" scanner - 30 kg (66.2 lb); 72" scanner - 33.4 kg (73.7 lb).

•The site must be clear of ropes and moving rigging.

•Sufficient clearance must be allowed to fully open the open array pedestal for maintenance.

Mounting surface: sailboats

The scanner unit can be installed on a mast platform, an arch, or a bridge structure. Make sure that the platform surface is flat and the scanner unit drain hole (radome scanners) is not obstructed. Raytheon recommends that radome scanner units are best suited for sailboat operation as open array systems are more difficult to protect from ropes and sails.

For sailboat installations, Raytheon offers a universal mast mount kit for each radome scanner type. This optional mount is used to fit a radome scanner to a flat surface on a mast with a minimum diameter of 60 mm (2½ in). When using the mast mount kit, appropriate hardware should be used for the style and structure of the mast aboard the vessel. Typically, the scanner will be mounted near the first set of mast spreaders. If there is any doubt concerning the appropriate type of hardware, consult your boat dealer or representative for their recommendations.

Depending on the type of sailboat, a radar scanner guard should be installed if the sails could touch the scanner or platform. Without a proper radar guard the mounting platform and the radar scanner could be severely damaged.

Mounting surface: power boats

On many small vessels the scanner unit can be installed on a mast platform, an arch, or a bridge structure, but take care to follow the scanner site guidelines, particularly regarding height. If necessary, construct a radar mounting platform to obtain a sufficiently high mounting position. Make sure that the platform surface is flat and the scanner unit drain hole (radome scanners) is not obstructed. Ensure the platform is strong enough to support the maximum shock loads likely to occur.

Image 17

Contents Pathfinder Radar Scanners Page October Pathfinder Radar Scanners Owners HandbookPathfinder Radar Scanners Display Software Version PrefaceWarranty Contents Appendix a Introduction OverviewThis handbook is divided into three chapters as follows EMC installation guidelinesConnections to Other Equipment Option Unpacking and inspecting the componentsSupplied with For Supplied with Option forSelecting the scanner unit site Radome Scanner Open Array Scanners WeightPathfinder Radar Scanners Mounting surface sailboats Mounting surface power boatsIdeal Radiation Plane Setting the radiation planeRejoining Cables Cable runsScanner Package Inter-Unit Cable Inter-unit cable2DE Eur Radome scanner cablesInter-Unit Cable Scanner Package Power cable Inter-Unit Cables Radome ScannerSystems 4 kW scanners only Open array scanner cables32 V Systems 4 kW scanners Inter-Unit Cable KW Scanners32 V Systems 10kW scanners 32 V systems Power Cable Core Size each coreKW Scanners Pathfinder Radar Scanners Installing the Scanner Connecting the radome scanner inter-unit cable Inner cover White wire Installing the Scanner Pathfinder Radar Scanners Open array scanner Securing the pedestal to the mounting platform Connecting the open array scanner inter-unit cable Heatshrink Heat Shrinking of Wires Do not grease the gasket in the pedestal lid Fitting the open array to the pedestal Power Connections DC power connectionSystem connections Grounding the radar systemVessels Device Open Array Systems Radome Supply 10 kW Scanner connectionScanner Front view Display Cable ConnectorDisplay Display unit connection Connector PanelsPathfinder Radar Scanners Switch on and initial set up Set up, alignment and timing checksSystem Checks and Alignment EMC ConformanceOpen array position alignment Display timing adjustmentChecking transmission Bearing alignmentRoutine Checks MaintenanceServicing and Safety Problem Correction Problem SolvingFor Marine Product and Services Information How to Contact Raytheon USFor Accessories and Parts For Technical SupportFor Product Repair and Service How to Contact Raytheon EuropeTechnical Support Accessories and PartsWorldwide Support Pathfinder Radar Scanners General 2D 18 Radome Scanner UnitTransmitter AntennaReceiver 4D 24 Radome Scanner UnitIncluding Low Noise Converter/Limiter & if Receiver Pulse Length/PRF 5S and 9S 48 Open Array Scanner Unit9S Transmitter 10 kW Appendix a SpecificationReceiver Noise Figure Less than 5 dB 7S Transmitter 4 kW 7S and 11S 72 Open Array Scanner Unit11S Transmitter 10 kW Appendix a Specification Pathfinder Radar Scanners Index Pathfinder Radar Scanners