Raymarine Radar Scanner manual Installing the Scanner

Page 29

Chapter 2: Installing the Scanner

21

Chapter 2: Installing the Scanner

2.1 Radome scanner

Securing the radome scanner to the mounting surface

CAUTION:

The drain tube must always be used, but may be shortened if necessary

1.Using the paper template supplied with the scanner mounting kit, mark the flat mounting surface with the mounting holes and drain tube hole, and drill the holes as indicated on the template.

If it is impractical to drill a hole for the drain tube, then the scanner unit should be mounted on 4 suitable spacers 10 mm high and the drain tube length reduced by 10 mm. It will then be clear of the flat surface and can still perform its function.

Note: If you are using a Raytheon mast mount bracket, the surface is pre-prepared.

Note: If you are mounting the scanner on a flat surface, you may find it easier to fit the drain tube, as described in the following section, be- fore securing the scanner.

2.Position the scanner on the mounting surface, ensuring that the cable inlet is pointing aft.

3.Locate the bolts and washers supplied with the scanner, grease the bolts, and secure the scanner to the mounting surface as shown in the following diagram. Tighten the bolts to 20 Nm (14.7 lb ft); ensure the scanner is tightly fitted.

Image 29

Contents Pathfinder Radar Scanners Page October Pathfinder Radar Scanners Owners HandbookPathfinder Radar Scanners Display Software Version PrefaceWarranty Contents Appendix a Introduction OverviewThis handbook is divided into three chapters as follows EMC installation guidelinesConnections to Other Equipment Option Unpacking and inspecting the componentsSupplied with For Supplied with Option forSelecting the scanner unit site Radome Scanner Open Array Scanners WeightPathfinder Radar Scanners Mounting surface sailboats Mounting surface power boatsIdeal Radiation Plane Setting the radiation planeRejoining Cables Cable runsScanner Package Inter-Unit Cable Inter-unit cable2DE Eur Radome scanner cablesInter-Unit Cable Scanner Package Power cable Inter-Unit Cables Radome ScannerSystems 4 kW scanners only Open array scanner cables32 V Systems 4 kW scanners Inter-Unit Cable KW Scanners32 V Systems 10kW scanners 32 V systems Power Cable Core Size each coreKW Scanners Pathfinder Radar Scanners Installing the Scanner Connecting the radome scanner inter-unit cable Inner cover White wire Installing the Scanner Pathfinder Radar Scanners Open array scanner Securing the pedestal to the mounting platform Connecting the open array scanner inter-unit cable Heatshrink Heat Shrinking of Wires Do not grease the gasket in the pedestal lid Fitting the open array to the pedestal Power Connections DC power connectionSystem connections Grounding the radar systemVessels Device Open Array Systems Radome Supply 10 kW Scanner connectionScanner Front view Display Cable ConnectorDisplay Display unit connection Connector PanelsPathfinder Radar Scanners Switch on and initial set up Set up, alignment and timing checksSystem Checks and Alignment EMC ConformanceOpen array position alignment Display timing adjustmentChecking transmission Bearing alignmentRoutine Checks MaintenanceServicing and Safety Problem Correction Problem SolvingFor Marine Product and Services Information How to Contact Raytheon USFor Accessories and Parts For Technical SupportFor Product Repair and Service How to Contact Raytheon EuropeTechnical Support Accessories and PartsWorldwide Support Pathfinder Radar Scanners General 2D 18 Radome Scanner UnitTransmitter AntennaReceiver 4D 24 Radome Scanner UnitIncluding Low Noise Converter/Limiter & if Receiver Pulse Length/PRF 5S and 9S 48 Open Array Scanner Unit9S Transmitter 10 kW Appendix a SpecificationReceiver Noise Figure Less than 5 dB 7S Transmitter 4 kW 7S and 11S 72 Open Array Scanner Unit11S Transmitter 10 kW Appendix a Specification Pathfinder Radar Scanners Index Pathfinder Radar Scanners