RF-Link Technology NL6000 Radio Network Setup, Setting the Unit Type Select Network ä Unit Type

Page 30

6.2. Radio Network Setup

Setting the Unit Type

1.Select Network ä Unit Type.

2.Select from the following options:

1-BaseConfigure as a base station. This unit type receives the TOID from the data packet received through the serial port.

2-RemoteConfigure as a remote. This unit type receives the TOID from its configuration.

Setting the Unit ID (MYID)

1.Select Network ä MYID.

2.Enter a unique identification for the unit. The value must be a hexadecimal value between 0001 and FFFE. For more information about addressing and wildcards, refer to Section 5.4.

Setting the Target Unit ID (TOID)

You only need to set this parameter if the Unit Type is Remote. The system ignores this parameter if the Unit Type is Base.

1.Select Network ä TOID.

2.Enter the destination address for packets from this unit. The destination address is the MYID of the unit for which the data is intended. The value must be a hexadecimal value in the range 0000 FFFF. For more information about addressing and wildcards, refer to Section 5.4.

Setting the Active Channel

1.Select Radio ä Select Active Channel.

2.Enter the channel assignment for this unit. The value must be a number in the range 01 64.

Setting the Receive Frequency

1.Select Radio ä Receive Frequency for Active Channel.

2.Enter the receive frequency for the active radio channel in MHz. The value must be a number in the format nnn.nnnn.

Setting the Transmit Frequency

1.Select Radio ä Transmit Frequency for Active Channel.

2.Enter the transmit frequency for the active radio channel in MHz. The value must be a number in the format nnn.nnnn.

RF Neulink

30

NL6000 User Guide

Image 30

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Use the NL6000 in a Simple Configuration Product OverviewFeatures Acknowledgement Configuration TemplatesSingle and Multi- Point Addressing Auto-TransmitFCC Part Safety WarningRegulatory Information 406.0 to 406.1 MHz OperationSpecifications General SpecificationsTransmitter UHF Radio SpecificationsCurrent Drain at 12 ReceiverVHF Radio Specifications Parts Description Hardware Installation and OperationPower Connections Serial PortDTE DCEOperation Antenna ConnectionLEDs LEDPrerequisites Software ConfigurationTechnical Support PreparationUnique Data Requirements for a Base Station Source and Destination AddressingBehavior of Repeater Units Addressing with WildcardsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Transmission Mode Packet Data OptionsCRC FECRF Neulink NL6000 User Guide Over-the-Air Data Rates AcknowledgementsSerial Connection to an I/O Device Carrier Sense Multiple AccessDCD Mode Basic Serial ParametersFactory Default Parameters Planning the RF ChannelPre- and Post-Data DCD Time Procedures Select Network ä Unit TypeGeneral Procedures Displaying the Configuration Summary Window Returning to the Previous MenuSetting the Unit ID Myid Select Network ä Myid Radio Network SetupSetting the Unit Type Select Network ä Unit Type Setting the Target Unit ID ToidSerial Connection Setup Data Setup Setting the Packet Mode Select Network ä Packet ModeSetting the Contention Option Select Network ä Contention Setting the Data Rate Select Network ä Data RateSetting the Request ACKs Option Setting the Max Retries OptionRepeater Setup Trigger ID Value UseDownloading a Software Upgrade File ManagementSelect Save/Restore Parameters ä Save Parameters to Disk Saving Parameters to DiskRestoring Parameters from Disk Restoring Default Parameters Menu Quick Reference Main Menu Summary WindowSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Troubleshooting Other ConsiderationsDuty Cycle Use a Slower Baud Rate Use a Fully-Wired RS-232 CableUnit Does Not Enter Programming Mode Use a Faster Baud RateSetting the Power Value Appendix a Diagnosing and Correcting Performance ProblemsSetting the Frequency Trim includes setting Power Select Diagnostics ä Transmit Continuous Random DataSelect Diagnostics ä Transmit 100 Hz Square Wave Setting the Deviation and Balance∙ Select Frequency Trim from the Diagnostics menu ∙ Select Radio Ä Transmit Frequency for Active Channel∙ Select Diagnostics ä Receive Diagnostic Mode Setting the Receive Gain∙ Select Deviation from the Diagnostics menu ∙ Select Diagnostics ä Receive GainAppendix B Factory Default Parameters Category Parameter Default Value Custom ValueFactory Default Values Index RF Neulink NL6000 User Guide