RF-Link Technology NL6000 manual General Specifications

Page 10

3. Specifications

GENERAL SPECIFICATIONS

Dimensions	3.0 in L x 2.6 in W x 1.6 in H
DC voltage input	Nominal 10-15 VDC
Operating temperature	-30° C to +60° C
Number of Channels	64
Number of ID codes	65,525
Over-the-air (Tx) data rate	12,000 bps or 22,050 bps
Serial port baud rates	1200 bps, 2400 bps, 4800 bps,
	9600 bps, 19.2 kbps, 28.8 kbps,
	38.4 kbps
RF input/output connector	SMA-F
Data interface	9-pin (DB9)
Serial interface	RS-232 async
Mode of operation	Simplex or Half Duplex
Frequency control	PLL synthesizer
Error control	3 data transmission modes provide
	progressively increasing error correction strength

RF Neulink

10

NL6000 User Guide

Image 10

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Use the NL6000 in a Simple Configuration Product OverviewFeatures Acknowledgement Configuration TemplatesSingle and Multi- Point Addressing Auto-TransmitFCC Part Safety WarningRegulatory Information 406.0 to 406.1 MHz OperationSpecifications General SpecificationsTransmitter UHF Radio SpecificationsCurrent Drain at 12 ReceiverVHF Radio Specifications Parts Description Hardware Installation and OperationPower Connections Serial PortDTE DCEOperation Antenna ConnectionLEDs LEDPrerequisites Software ConfigurationTechnical Support PreparationUnique Data Requirements for a Base Station Source and Destination AddressingBehavior of Repeater Units Addressing with WildcardsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Transmission Mode Packet Data OptionsCRC FECRF Neulink NL6000 User Guide Over-the-Air Data Rates AcknowledgementsSerial Connection to an I/O Device Carrier Sense Multiple AccessDCD Mode Basic Serial ParametersPlanning the RF Channel Factory Default ParametersPre- and Post-Data DCD Time Procedures Select Network ä Unit TypeGeneral Procedures Displaying the Configuration Summary Window Returning to the Previous MenuSetting the Unit ID Myid Select Network ä Myid Radio Network SetupSetting the Unit Type Select Network ä Unit Type Setting the Target Unit ID ToidSerial Connection Setup Data Setup Setting the Packet Mode Select Network ä Packet ModeSetting the Contention Option Select Network ä Contention Setting the Data Rate Select Network ä Data RateSetting the Request ACKs Option Setting the Max Retries OptionRepeater Setup Trigger ID Value UseDownloading a Software Upgrade File ManagementSaving Parameters to Disk Select Save/Restore Parameters ä Save Parameters to DiskRestoring Parameters from Disk Restoring Default Parameters Menu Quick Reference Main Menu Summary WindowSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Other Considerations TroubleshootingDuty Cycle Use a Slower Baud Rate Use a Fully-Wired RS-232 CableUnit Does Not Enter Programming Mode Use a Faster Baud RateSetting the Power Value Appendix a Diagnosing and Correcting Performance ProblemsSetting the Frequency Trim includes setting Power Select Diagnostics ä Transmit Continuous Random DataSelect Diagnostics ä Transmit 100 Hz Square Wave Setting the Deviation and Balance∙ Select Frequency Trim from the Diagnostics menu ∙ Select Radio Ä Transmit Frequency for Active Channel∙ Select Diagnostics ä Receive Diagnostic Mode Setting the Receive Gain∙ Select Deviation from the Diagnostics menu ∙ Select Diagnostics ä Receive GainCategory Parameter Default Value Custom Value Appendix B Factory Default ParametersFactory Default Values Index RF Neulink NL6000 User Guide