RF-Link Technology NL6000 manual Repeat from a Base to a Remote

Page 19

Consider the following example of a repeater (MYID3000) configured to repeat packets transmitted from a base station (MYID2000) to a hidden remote (MYID4203). Unit MYID3000 is configured with a repeater entry that has a Trigger = TOID and ID = 4203. This entry tells unit MYID3000 to listen for packets that have a destination address of TOID4203. If the repeater receives a packet matching the criteria, it immediately repeats the packet. Figure 10 illustrates this scenario.

Figure 10: Repeat from a Base to a Remote

Consider the following example of a repeater (MYID3000) configured to repeat packets transmitted from a hidden remote (TOID4201) to a base station (TOID2000). Unit MYID3000 is configured with a repeater entry that has a Trigger = MYID and ID = 4201. This entry tells unit MYID3000 to listen for packets that have a source address of MYID4201. If the repeater receives a packet matching the criteria, it immediately repeats the packet. Figure 11 illustrates this scenario.

Figure 11: Repeat from a Remote to a Base Station

Because MYID and TOID values may use wildcards, it is possible to set up a single repeater entry that will repeat all packets destined to a group of hidden remotes. In Figure 12, a repeater entry with a Trigger = TOID and ID = 42FF repeats any packet with a destination matching TOID42FF.

RF Neulink

19

NL6000 User Guide

Image 19

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Product Overview Use the NL6000 in a Simple ConfigurationFeatures Auto-Transmit Configuration TemplatesSingle and Multi- Point Addressing Acknowledgement406.0 to 406.1 MHz Operation Safety WarningRegulatory Information FCC PartGeneral Specifications SpecificationsReceiver UHF Radio SpecificationsCurrent Drain at 12 TransmitterVHF Radio Specifications Serial Port Hardware Installation and OperationPower Connections Parts DescriptionDCE DTELED Antenna ConnectionLEDs OperationPreparation Software ConfigurationTechnical Support PrerequisitesSource and Destination Addressing Unique Data Requirements for a Base StationAddressing with Wildcards Behavior of Repeater UnitsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Packet Data Options Transmission ModeFEC CRCRF Neulink NL6000 User Guide Acknowledgements Over-the-Air Data RatesBasic Serial Parameters Carrier Sense Multiple AccessDCD Mode Serial Connection to an I/O DevicePlanning the RF Channel Factory Default ParametersPre- and Post-Data DCD Time Select Network ä Unit Type ProceduresGeneral Procedures Returning to the Previous Menu Displaying the Configuration Summary WindowSetting the Target Unit ID Toid Radio Network SetupSetting the Unit Type Select Network ä Unit Type Setting the Unit ID Myid Select Network ä MyidSerial Connection Setup Setting the Packet Mode Select Network ä Packet Mode Data SetupSetting the Max Retries Option Setting the Data Rate Select Network ä Data RateSetting the Request ACKs Option Setting the Contention Option Select Network ä ContentionTrigger ID Value Use Repeater SetupFile Management Downloading a Software UpgradeSaving Parameters to Disk Select Save/Restore Parameters ä Save Parameters to DiskRestoring Parameters from Disk Restoring Default Parameters Main Menu Summary Window Menu Quick ReferenceSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Other Considerations TroubleshootingDuty Cycle Use a Faster Baud Rate Use a Fully-Wired RS-232 CableUnit Does Not Enter Programming Mode Use a Slower Baud RateSelect Diagnostics ä Transmit Continuous Random Data Appendix a Diagnosing and Correcting Performance ProblemsSetting the Frequency Trim includes setting Power Setting the Power Value∙ Select Radio Ä Transmit Frequency for Active Channel Setting the Deviation and Balance∙ Select Frequency Trim from the Diagnostics menu Select Diagnostics ä Transmit 100 Hz Square Wave∙ Select Diagnostics ä Receive Gain Setting the Receive Gain∙ Select Deviation from the Diagnostics menu ∙ Select Diagnostics ä Receive Diagnostic ModeCategory Parameter Default Value Custom Value Appendix B Factory Default ParametersFactory Default Values Index RF Neulink NL6000 User Guide