RF-Link Technology NL6000 manual Restoring Default Parameters

Page 37

to restore parameters at this time, press ESC.

When you press Y, the system erases the current parameter file in flash memory.

4.When the system prompts you to send the parameter file, initiate the restore using the terminal emulator.

∙If you use Procomm, use the Send ASCII Text option.

∙If you use HyperTerminal, use the Send Text File option.

A success message appears when the restore is complete.

5.When the download is complete, cycle power to let the modem start using the new parameter settings.

6.Press ESC to continue using the Save/Restore Parameters menu.

Restoring Default Parameters

Use the following procedure to restore factory-delivered default parameter settings to the unit currently attached to the serial port.

1.Select Save/Restore Parameters ä Restore Default Parameters. The system prompts you to confirm that you want to restore the default parameter settings.

2.Press Y to confirm that you want to restore the default settings. If you do not want to restore default settings at this time, press ESC.

When you press Y, the system erases the parameter file in flash memory and restores the default settings. A success message appears when the restore is complete.

3.When the download is complete, cycle power to let the modem start using the new parameter settings.

4.Press ESC to continue using the Save/Restore Parameters menu.

RF Neulink

37

NL6000 User Guide

Image 37

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Product Overview Use the NL6000 in a Simple ConfigurationFeatures Single and Multi- Point Addressing Configuration TemplatesAcknowledgement Auto-TransmitRegulatory Information Safety WarningFCC Part 406.0 to 406.1 MHz OperationGeneral Specifications SpecificationsCurrent Drain at 12 UHF Radio SpecificationsTransmitter ReceiverVHF Radio Specifications Power Connections Hardware Installation and OperationParts Description Serial PortDCE DTELEDs Antenna ConnectionOperation LEDTechnical Support Software ConfigurationPrerequisites PreparationSource and Destination Addressing Unique Data Requirements for a Base StationAddressing with Wildcards Behavior of Repeater UnitsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Packet Data Options Transmission ModeFEC CRCRF Neulink NL6000 User Guide Acknowledgements Over-the-Air Data RatesDCD Mode Carrier Sense Multiple AccessSerial Connection to an I/O Device Basic Serial ParametersPlanning the RF Channel Factory Default ParametersPre- and Post-Data DCD Time Select Network ä Unit Type ProceduresGeneral Procedures Returning to the Previous Menu Displaying the Configuration Summary WindowSetting the Unit Type Select Network ä Unit Type Radio Network SetupSetting the Unit ID Myid Select Network ä Myid Setting the Target Unit ID ToidSerial Connection Setup Setting the Packet Mode Select Network ä Packet Mode Data SetupSetting the Request ACKs Option Setting the Data Rate Select Network ä Data RateSetting the Contention Option Select Network ä Contention Setting the Max Retries OptionTrigger ID Value Use Repeater SetupFile Management Downloading a Software UpgradeSaving Parameters to Disk Select Save/Restore Parameters ä Save Parameters to DiskRestoring Parameters from Disk Restoring Default Parameters Main Menu Summary Window Menu Quick ReferenceSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Other Considerations TroubleshootingDuty Cycle Unit Does Not Enter Programming Mode Use a Fully-Wired RS-232 CableUse a Slower Baud Rate Use a Faster Baud RateSetting the Frequency Trim includes setting Power Appendix a Diagnosing and Correcting Performance ProblemsSetting the Power Value Select Diagnostics ä Transmit Continuous Random Data∙ Select Frequency Trim from the Diagnostics menu Setting the Deviation and BalanceSelect Diagnostics ä Transmit 100 Hz Square Wave ∙ Select Radio Ä Transmit Frequency for Active Channel∙ Select Deviation from the Diagnostics menu Setting the Receive Gain∙ Select Diagnostics ä Receive Diagnostic Mode ∙ Select Diagnostics ä Receive GainCategory Parameter Default Value Custom Value Appendix B Factory Default ParametersFactory Default Values Index RF Neulink NL6000 User Guide