RF-Link Technology
NL6000
manual
Radio Menu Diagnostics Menu
Troubleshooting
Specifications
Factory Default Parameters
NL6000 Wireless Modem
Configuration Templates
Radio Menu Diagnostics Menu
Carrier Sense Multiple Access
Radio Network Setup
Procedures
Setting the Power Value
Page 41
7.7.
Radio Menu
7.8.
Diagnostics Menu
RF Neulink
41
NL6000 User Guide
Page 40
Page 42
Image 41
Page 40
Page 42
Contents
NL6000 Wireless Modem
Copyright
Table of Contents
RF Neulink NL6000 User Guide
RF Neulink NL6000 User Guide
Product Overview
Use the NL6000 in a Simple Configuration
Features
Single and Multi- Point Addressing
Configuration Templates
Acknowledgement
Auto-Transmit
Regulatory Information
Safety Warning
FCC Part
406.0 to 406.1 MHz Operation
General Specifications
Specifications
Current Drain at 12
UHF Radio Specifications
Transmitter
Receiver
VHF Radio Specifications
Power Connections
Hardware Installation and Operation
Parts Description
Serial Port
DCE
DTE
LEDs
Antenna Connection
Operation
LED
Technical Support
Software Configuration
Prerequisites
Preparation
Source and Destination Addressing
Unique Data Requirements for a Base Station
Addressing with Wildcards
Behavior of Repeater Units
Repeat from a Base to a Remote
Repeat to Multiple Remotes using Wildcard
Packet Data Options
Transmission Mode
FEC
CRC
RF Neulink NL6000 User Guide
Acknowledgements
Over-the-Air Data Rates
DCD Mode
Carrier Sense Multiple Access
Serial Connection to an I/O Device
Basic Serial Parameters
Pre- and Post-Data DCD Time
Factory Default Parameters
Planning the RF Channel
Select Network ä Unit Type
Procedures
General Procedures
Returning to the Previous Menu
Displaying the Configuration Summary Window
Setting the Unit Type Select Network ä Unit Type
Radio Network Setup
Setting the Unit ID Myid Select Network ä Myid
Setting the Target Unit ID Toid
Serial Connection Setup
Setting the Packet Mode Select Network ä Packet Mode
Data Setup
Setting the Request ACKs Option
Setting the Data Rate Select Network ä Data Rate
Setting the Contention Option Select Network ä Contention
Setting the Max Retries Option
Trigger ID Value Use
Repeater Setup
File Management
Downloading a Software Upgrade
Restoring Parameters from Disk
Select Save/Restore Parameters ä Save Parameters to Disk
Saving Parameters to Disk
Restoring Default Parameters
Main Menu Summary Window
Menu Quick Reference
Serial Menu DCD RS-232 SubMenu
Network Menu Repeater SubMenu
Radio Menu Diagnostics Menu
Save/Restore Parameters Menu
Duty Cycle
Troubleshooting
Other Considerations
Unit Does Not Enter Programming Mode
Use a Fully-Wired RS-232 Cable
Use a Slower Baud Rate
Use a Faster Baud Rate
Setting the Frequency Trim includes setting Power
Appendix a Diagnosing and Correcting Performance Problems
Setting the Power Value
Select Diagnostics ä Transmit Continuous Random Data
∙ Select Frequency Trim from the Diagnostics menu
Setting the Deviation and Balance
Select Diagnostics ä Transmit 100 Hz Square Wave
∙ Select Radio Ä Transmit Frequency for Active Channel
∙ Select Deviation from the Diagnostics menu
Setting the Receive Gain
∙ Select Diagnostics ä Receive Diagnostic Mode
∙ Select Diagnostics ä Receive Gain
Factory Default Values
Appendix B Factory Default Parameters
Category Parameter Default Value Custom Value
Index
RF Neulink NL6000 User Guide
Related pages
All Diagnostic page
System unitonline startsdiagnostics for IBM RS/6000 7043 43P
Diagnostic lights for Dell Workstation 530
Service books and diagnostic reports for Blackberry 8220
Creating a Diagnostic Listing VIA FTP for Exabyte 1X7 LTO
Diagnostic for Moxa boards only for Moxa Technologies RS-422
Local Diagnostics for Nortel Networks 1140E
Diagnostics menu for HP DV6
Köra Dell Diagnostics for Dell T3913
DIAGnosticINTerruptLINE for Agilent Technologies E1563A
NIC Doctor Diagnostics Do Not Work for HP 3Com 3C905B D7523A
What sewing techniques can I use with the
Singer 177C
?
Top
Page
Image
Contents