RF-Link Technology manual RF Neulink NL6000 User Guide

Page 50

Power value, 47 Pre-Data DCD Time, 34 procedures, 29 Program Mode, 30

R

Radio Menu, 43

Receive Frequency for Active Channel,

32

Receive Gain, 49 regulatory information, 9 Repeater Submenu, 42 repeater units behavior, 19

frequency planning, 21 setup, 36

Request ACKs, 35 Restart, 30

Restore Default Parameters, 39 Restore Parameters from Disk, 39 restoring

default parameters, 39 parameters from disk, 38

returning to the previous menu, 31 reverting to the prior configuration, 30 RF channel, planning, 28

S

safety warnings, 9

Save Parameters to Disk, 38 Save/Restore Parameters Menu, 44 saving

configuration changes temporarily, 30 configuration changes to flash, 30 parameters to disk, 38

Select Repeater Entry, 36

selecting the repeater entry to edit, 36 Serial Menu, 41

serial parameters, basic, 26

serial port connector, 13 setting

the active channel, 32 the baud rate, 33

the contention option, 35 the data bits, 33 the data rate, 35 the

DCD mode, 33

the flow control option, 33 the maximum packet size, 34 the packet mode, 34

the post-data DCD time, 34 the pre-data DCD time, 34 the program mode, 30

the receive frequency, 32

the repeater transmit channel, 37 the repeater transmit delay, 37 the repeater trigger, 36

the repeater trigger ID, 37 the request ACKs option, 35 the stop bits, 33

the target unit ID, 32

the transmit character timeout, 33 the transmit frequency, 32

the unit ID, 32 the unit type, 32

setting the maximum retries option, 35 specifications, 11

Stop Bits, 33

Summary window, 31, 40 support, technical, 16

T

TOID, 32

transmission mode. See packet mode Transmit Channel, 37

Transmit Character Timeout, 33

Transmit Delay, 22, 37

Transmit Frequency for Active Channel, 32

Trigger, 36 troubleshooting, 45

U

Unit Type, 32

RF Neulink

50

NL6000 User Guide

Image 50

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Use the NL6000 in a Simple Configuration Product OverviewFeatures Acknowledgement Configuration TemplatesSingle and Multi- Point Addressing Auto-TransmitFCC Part Safety WarningRegulatory Information 406.0 to 406.1 MHz OperationSpecifications General SpecificationsTransmitter UHF Radio SpecificationsCurrent Drain at 12 ReceiverVHF Radio Specifications Parts Description Hardware Installation and OperationPower Connections Serial PortDTE DCEOperation Antenna ConnectionLEDs LEDPrerequisites Software ConfigurationTechnical Support PreparationUnique Data Requirements for a Base Station Source and Destination AddressingBehavior of Repeater Units Addressing with WildcardsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Transmission Mode Packet Data OptionsCRC FECRF Neulink NL6000 User Guide Over-the-Air Data Rates AcknowledgementsSerial Connection to an I/O Device Carrier Sense Multiple AccessDCD Mode Basic Serial ParametersPre- and Post-Data DCD Time Factory Default ParametersPlanning the RF Channel Procedures Select Network ä Unit TypeGeneral Procedures Displaying the Configuration Summary Window Returning to the Previous MenuSetting the Unit ID Myid Select Network ä Myid Radio Network SetupSetting the Unit Type Select Network ä Unit Type Setting the Target Unit ID ToidSerial Connection Setup Data Setup Setting the Packet Mode Select Network ä Packet ModeSetting the Contention Option Select Network ä Contention Setting the Data Rate Select Network ä Data RateSetting the Request ACKs Option Setting the Max Retries OptionRepeater Setup Trigger ID Value UseDownloading a Software Upgrade File ManagementRestoring Parameters from Disk Select Save/Restore Parameters ä Save Parameters to DiskSaving Parameters to Disk Restoring Default Parameters Menu Quick Reference Main Menu Summary WindowSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Duty Cycle TroubleshootingOther Considerations Use a Slower Baud Rate Use a Fully-Wired RS-232 CableUnit Does Not Enter Programming Mode Use a Faster Baud RateSetting the Power Value Appendix a Diagnosing and Correcting Performance ProblemsSetting the Frequency Trim includes setting Power Select Diagnostics ä Transmit Continuous Random DataSelect Diagnostics ä Transmit 100 Hz Square Wave Setting the Deviation and Balance∙ Select Frequency Trim from the Diagnostics menu ∙ Select Radio Ä Transmit Frequency for Active Channel∙ Select Diagnostics ä Receive Diagnostic Mode Setting the Receive Gain∙ Select Deviation from the Diagnostics menu ∙ Select Diagnostics ä Receive GainFactory Default Values Appendix B Factory Default ParametersCategory Parameter Default Value Custom Value Index RF Neulink NL6000 User Guide