RF-Link Technology NL6000 manual Index

Page 49

Index

A

acknowledgements, 26 Active Channel, 32

addressing, source and destination, 18 antenna connection, 15

B

Balance, 48

base station unique requirements, 18

C

carrier sense multiple access. See CSMA configuration

preparation, 17 prerequisites, 17 procedures, 29

Contention, 35

Continue, 30

CSMA, 26

D

Data Bits, 33 Data Rate, 26, 35 DCD Mode, 27, 33 DCD time, 27 DCD232 Submenu, 41 Deviation, 48 diagnostics, 47 Diagnostics Menu, 43

displaying the configuration summary window, 31

Download New Software, 38 downloading a software upgrade, 37 duty cycle, 45

E

entering programming mode, 30 Esc key, 31

Exit, 30

F

factory default parameters, 28, 51 file management procedures, 37 Flow Control, 27, 33 Frequency Trim, 47

H

hardware installation, 13

I

ID, 37

L

LEDs, 15

M

Main Menu, 40

Max Packet Size, 25, 34 Max Retries, 26, 35 menu windows, 40 MYID, 32

N

Network Menu, 42 NL6000

product overview, 6 specifications, 11

O

operation, 15

P

packet mode

Basic Telemetry, 24 considerations, 23 description of types, 23

Enhanced Telemetry, 24

Mobile Data, 25

Packet Mode, 34 parts description, 13

performance problems correcting, 47 diagnosing, 47

Post-Data DCD Time, 34 power connections, 13

power output and duty cycle, 45

RF Neulink

49

NL6000 User Guide

Image 49

Contents NL6000 Wireless Modem Copyright Table of Contents RF Neulink NL6000 User Guide RF Neulink NL6000 User Guide Product Overview Use the NL6000 in a Simple ConfigurationFeatures Single and Multi- Point Addressing Configuration TemplatesAcknowledgement Auto-TransmitRegulatory Information Safety WarningFCC Part 406.0 to 406.1 MHz OperationGeneral Specifications SpecificationsCurrent Drain at 12 UHF Radio SpecificationsTransmitter ReceiverVHF Radio Specifications Power Connections Hardware Installation and OperationParts Description Serial PortDCE DTELEDs Antenna ConnectionOperation LEDTechnical Support Software ConfigurationPrerequisites PreparationSource and Destination Addressing Unique Data Requirements for a Base StationAddressing with Wildcards Behavior of Repeater UnitsRepeat from a Base to a Remote Repeat to Multiple Remotes using Wildcard Packet Data Options Transmission ModeFEC CRCRF Neulink NL6000 User Guide Acknowledgements Over-the-Air Data RatesDCD Mode Carrier Sense Multiple AccessSerial Connection to an I/O Device Basic Serial ParametersPlanning the RF Channel Factory Default ParametersPre- and Post-Data DCD Time Select Network ä Unit Type ProceduresGeneral Procedures Returning to the Previous Menu Displaying the Configuration Summary WindowSetting the Unit Type Select Network ä Unit Type Radio Network SetupSetting the Unit ID Myid Select Network ä Myid Setting the Target Unit ID ToidSerial Connection Setup Setting the Packet Mode Select Network ä Packet Mode Data SetupSetting the Request ACKs Option Setting the Data Rate Select Network ä Data RateSetting the Contention Option Select Network ä Contention Setting the Max Retries OptionTrigger ID Value Use Repeater SetupFile Management Downloading a Software UpgradeSaving Parameters to Disk Select Save/Restore Parameters ä Save Parameters to DiskRestoring Parameters from Disk Restoring Default Parameters Main Menu Summary Window Menu Quick ReferenceSerial Menu DCD RS-232 SubMenu Network Menu Repeater SubMenu Radio Menu Diagnostics Menu Save/Restore Parameters Menu Other Considerations TroubleshootingDuty Cycle Unit Does Not Enter Programming Mode Use a Fully-Wired RS-232 CableUse a Slower Baud Rate Use a Faster Baud RateSetting the Frequency Trim includes setting Power Appendix a Diagnosing and Correcting Performance ProblemsSetting the Power Value Select Diagnostics ä Transmit Continuous Random Data∙ Select Frequency Trim from the Diagnostics menu Setting the Deviation and BalanceSelect Diagnostics ä Transmit 100 Hz Square Wave ∙ Select Radio Ä Transmit Frequency for Active Channel∙ Select Deviation from the Diagnostics menu Setting the Receive Gain∙ Select Diagnostics ä Receive Diagnostic Mode ∙ Select Diagnostics ä Receive GainCategory Parameter Default Value Custom Value Appendix B Factory Default ParametersFactory Default Values Index RF Neulink NL6000 User Guide