Trango Broadband M5580M-FSU user manual Set baseid baseid, Set suid suid

Page 14

Configuration

Subscriber Unit Basic Settings

Log into the SU. To receive a comprehensive snapshot of the system’s configuration info and status, type the command sysinfo.

#> sysinfo

[Hardware Version] 5580

[MVC Version] 3893mvc_4p5_050913.arm

[Firmware Version] AFSU 2p0r8D06011801

[Device ID] 00 01 DE 00 04 3F [Base ID] 1 [AP ID] 1 [SU ID] 1 [System Up Time] 0 day(s) 00:00:39

[Opmode] off [Default Opmode] off [Opmode Start] 30 sec

[IP] 192.168.100.100 [Subnet Mask] 255.255.255.0 [Gateway] 192.168.100.1 [Httpd Port] 80 [Httpd Status] listen

[Telnetd Port] 23 [Telnetd Status] connected [Telnet Client #1] 192.168.100.177,1637 [Tftpd] disabled

[RF Tx Power] 17 dBm

Channel Table: (MHz)

[Ch#01] 5736 [Ch#02] 5756 [Ch#03] 5776 [Ch#04] 5796 [Ch#05] 5816 [Ch#06] 5836

[Ch#07] 5736 [Ch#08] 5736 [Ch#09] 5736 [Ch#10] 5736 [Ch#11] 5736 [Ch#12] 5736

[Ch#13] 5736 [Ch#14] 5736 [Ch#15] 5736 [Ch#16] 5736 [Ch#17] 5736 [Ch#18] 5736

[Ch#19] 5736 [Ch#20] 5736 [Ch#21] 5736 [Ch#22] 5736 [Ch#23] 5736 [Ch#24] 5736

[Ch#25] 5736 [Ch#26] 5736 [Ch#27] 5736 [Ch#28] 5736 [Ch#29] 5736 [Ch#30] 5736

[Channel Scan Sequence] 5 v [Active Channel] 5 v Disconnected

[Broadcast Packet] on [Auto Scan AP] on [TCP/IP for AP] off [TCP/IP for Local Eth] off [Remarks] Remarks

[ARQ] on

[RF Rx] 0 Kbps [RF Tx] 0 Kbps [Eth Rx] 0 Kbps [Eth Tx] 0 Kbps

[Eth Rx] 1,629 bytes [Eth Tx] 2,812 bytes [RF Rx] 0 bytes [RF Tx] 0 bytes

Success.

Many of these parameters can be changed by the user. A description of each of these changeable parameters, along with the related command, is shown in table #3 below.

Table 2: Reference Table of Basic SU System Information

 

SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

 

 

SU Parameter

 

Description

Related CLI Command

 

 

Device ID

 

MAC Address of the SU

N/A

 

 

Base ID

 

Specifies the cell or cluster to

set baseid <baseid>

 

 

 

 

which the SU belongs.

 

 

 

 

 

 

Example: #>Set baseid 10

 

 

 

 

 

 

 

 

SU ID

 

Together with Base ID, it is

set suid <suid>

 

 

 

 

the unique identifier of this SU

 

 

 

 

 

used in association. It is used

Example:

 

 

 

 

 

 

 

 

Trango Broadband Wireless — M5580M-FSU (Atlas Fox) User Manual Revision 2

page 10

 

Image 14
Contents February 13 Revision For Firmware V.2p0r8 Appendix B FCC Information Warranty InformationPreface Overview Range vs. Throughput System Contents Location of Serial Number & MAC Address Location of RJ-45/LED Port Connections and Power Getting StartedTelnet ip address of radio Configuration ToolsTroubleshooting Ethernet Connections System Information sysinfo # sysinfoAccess Point Basic Settings ConfigurationEssentials to Establish a Wireless Link Key ConceptsSet baseid baseid Set suid suidPower set dBm Range is Set defaultopmode su offIpconfig new ip new subnet mask new Sw 0 on off default is onEstablishing a Wireless Link Changing IP Address LEDsPower Settings Using the Http Interface Configure Basic ParametersConfigure Basic Configure Basic Configure Basic Continuo Site survey Deployment & InstallationSite Selection Rssi Command and Antenna Alignment Channel PlanningRF Link Loopback Test linktest command Strain relief and boot installation Mounting HardwareM5580M-FSU Series SU Wall Mount M5580M FSU / AD5800 -25 Reflector Dish on Pole Cabling and Weather Considerations WeatherizingSnmp Firmware Upgrade Procedure Example #tftpd onCommand RemarksAppendix a Specifications Data Parameters